Cozzia EC-326G-CO страница 2 Скачать руководство пользователя | Manualshive

Страница: 2 / 58

background image

CATALOG

1: Precautions for inspection and repair
2: Massage chair auto-check list
3: Common Troubles and Maintenance Methods list.
4: Tools List
5-1:Guidance of disassemble the backrest pad assy
5-2: Guidance of disassemble the backrest
5-3: Guidance of detach front cover & rear cover of backrest.
5-4: Guidance of detach up & down limit sensor
5-5: Guidance of detach the kneading motor.
5-6: Guidance of change the counting sensor of rolling motor
5-7: Guidance of disassemble the massage mechanism
5-8: Guidance of change rolling motor unit.
5-9:Guidance of service the seat pad assy
5-10:Guidance of disassemble the side board.
5-11: Guidance of disassemble main PCB
5-12: Guidance of disassemble the Transformer
5-13: Guidance of disassemble the Air valve.
5-14: Guidance of disassemble Inflator Pump
5-15: Guidance of disassemble the remote control
5-16: Guidance of disassemble footrest actuator and backrest actuator
5-17: Guidance of change the lower side board
5-18: Guidance of service the footrest.
6: Main PCB connecter diagram.

«
1
2
3
4
...
»

Содержание EC-326G-CO



























































Отзывы:

Нет отзывов

Похожие инструкции для EC-326G-CO

Бренд: Katana Страницы: 38

InstaShiatsu+ IS-6000

Бренд: truMedic Страницы: 20

Бренд: Casada Страницы: 26

Бренд: Fujimedic Страницы: 44

Бренд: aidapt Страницы: 2

Бренд: aidapt Страницы: 6

Бренд: Body Mate Страницы: 4

Бренд: Melissa Страницы: 15

Бренд: Ironman Fitness Страницы: 9

Бренд: Eurotops Страницы: 18

Бренд: Saneo Страницы: 44

Бренд: Panasonic Страницы: 17

Бренд: Panasonic Страницы: 49

Бренд: Ogawa Страницы: 52

Restore Hot & Cold Foot Roller

Бренд: Gaiam Страницы: 2

Бренд: Hudora Страницы: 8

Бренд: TEBO Страницы: 30

Бренд: Insportline Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды