![background image](http://html1.mh-extra.com/html/covidien/warmtouch/warmtouch_service-manual_2673928243.webp)
Front Enclosure Replacement
Service Manual
12-11
13.
Install the AC power inlet in the new enclosure as follows (
a.
Position the AC power inlet assembly as shown in
.
b.
Attach the AC power inlet to the enclosure with the two screws. Tighten the
screws to 0.4 to 0.6 N-m (3.5 to 5.3 lb-in).
c.
Connect the 6-pin connector of the AC power inlet wire assembly to P112 on
the Power PCBA. Make sure that the connector is oriented as shown in
, and that it is fully seated.
d.
Connect the 3-pin connector of the wire assembly to CON1 on the power
supply. Make sure that the connector latch engages.
Note:
If a cable tie previously secured the AC power inlet wire assembly to the
power supply mounting boss (see
), install a new cable tie at the same
position. The cable tie should cause the wires connected to CON1 to form an arch
approximately 4 cm (1.5 in) above the connector. Trim off the end of the cable tie.
14.
Install the equipotential stud in the new enclosure as follows (
a.
From the bottom of the enclosure, insert the threaded end of the stud, with
the ground washer attached, into the hole.
b.
Place the AC power inlet ground cable terminal on the threaded end of the
stud. See
for the order of items on the stud.
c.
Place a lock washer on top of the terminal.
d.
Place a nut on top of the lock washer. Tighten the nut to 3.2 to 3.8 N-m (28.3
to 33.6 lb-in).
e.
Place the power supply ground cable terminal on top of the nut.
f.
Place a lock washer on top of the terminal.
g.
Place a nut on top of the lock washer. Tighten the nut to 3.2 to 3.8 N-m (28.3
to 33.6 lb-in).
15.
Follow the procedure
Rejoining the Front and Rear Enclosures
16.
Perform the following tests:
a.
b.
c.
d.
e.
f.
Содержание WarmTouch
