Courion iDRIVE Скачать руководство пользователя страница 22

Страница: 22 / 64

ver.071217-2.10

iLEARN

System Manual

iLEARN Door Control Menu Screens

(continued)

NOTE

: Using the MENU/Select Knob, select the appropriate iDRIVE VFD Control. iDRIVE

Unit Addresses (e.g. 01, 02, 03) correspond to their position on your COURION CANbus

Network.

1.3.1 Comm Rate -

This is the number of good command/reply transactions between the iL-

earn and this drive in the last second. Approximately 240 transactions per second are shared

by all slaves on the network. For example, if there are 6 door openings and 2 car gates, this

number would be around 30 for a noise free network.

1.3.2 Open iSENSOR Flags -

07 – This bit indicates the last detected direction of motion. ‘1’

indicates that the door magnet is moving TOWARDS the Open iSENSOR (Open Direction); ‘0’

indicates that the door magnet is moving AWAY from the Open iSENSOR (Close Direction).

1.3.3 Open iSENSOR Position -

Used to indicate door position relative to FULL OPEN. This

is not done initially because these values are relative to door position when the iSENSORs are

powered up. If powered up at FULL OPEN, then the position will be near 12”.

1.3.4 Full Open Position -

This is the value of the “Open iSENSOR Position” register where

the door stalls in the open position.

1.3.5 Open iSENSOR Speed -

This is actually the period between alternating poles. It is non-

zero when the magnet is moving over the sensor and zero when the magnet is not moving.

1.3.6 Close iSENSOR Flags -

07 – This bit indicates the last detected direction of motion. ‘1’

indicates that the door magnet is moving TOWARDS the Closed iSENSOR (Close Direction);

‘0’ indicates that the door magnet is moving AWAY from the Close iSENSOR (Open Direction).

1.3.7 Close iSENSOR Position -

Used to indicate door position relative to FULL CLOSE. This

is not done initially because these values are relative to door position when the iSENSORs are

powered up. If powered up at FULL OPEN, then the position will be near 0”.

1.3.8 Close Limit Position -

This is the value of the “Close iSENSOR Position” register where

the door stalls in the closed position.

1.3.9 Close iSENSOR Speed -

This is actually the period between alternating poles. It is non-

zero when the magnet is moving over the sensor and zero when the magnet is not moving.

1.3.10 Digital Inputs (iDRIVE VFD Control) -

These bits represent the state of the digital

inputs presented to the iDrive. A ‘1’ indicates a CLOSED circuit. A ‘0’ represents an OPEN

circuit.

06 - Request For Address - is provided by the previous iDRIVE or iLEARN in the network

Содержание iDRIVE

































































Результаты поиска

Содержание iDRIVE

Отзывы:

Бренды по названию

Популярные бренды

Courion iDRIVE, Системное руководство

Результаты поиска

Содержание iDRIVE

Отзывы:

Бренды по названию

Популярные бренды