Courion iDRIVE Скачать руководство пользователя страница 10

Страница: 10 / 64

ver.071217-2.10

iLEARN

System Manual

b. Enter the

# of Hoistway iDRIVE

s (both front and rear openings) in your

hoistway.

c. Enter the

# of Car Gates

(1 or 2) in your hoistway. System Default = 0.

d. Enter the

Car Top Control Type

(iDRIVE.G or iDRIVE.PLC). See label on

Car Top Control Enclosure for Car Top Control Type.

e. Enter the

# of Car Stations

(1 or 2) in your hoistway. System Default = 2.

f. Enter Gate Travel (generally the height of your Opening). System Default =

96”.

g. Set the correct Time and Date for your System.

h. If you have entered 1 or 2 Car Gates during Step #9 above, then select

Yes to set up the FULL OPEN and FULL CLOSE position for your Front and

Rear Gate.

i. Close the Front (Rear) Gate and push the COP Close Button.

Содержание iDRIVE

































































Результаты поиска

Содержание iDRIVE

Отзывы:

Похожие инструкции для iDRIVE

Бренды по названию

Популярные бренды

Courion iDRIVE, Системное руководство

Результаты поиска

Содержание iDRIVE

Отзывы:

Похожие инструкции для iDRIVE

Бренды по названию

Популярные бренды