Courion iDRIVE Скачать руководство пользователя страница 11

Страница: 11 / 64

ver.071217-2.10

iLEARN

System Manual

j. Open the Front (Rear) Gate and push the COP Open Button.

The iDRIVE.G Car Top Control Box now has set your FULL OPEN and FULL

Close position.

Using the MENU/SELECT Button, Exit back to the Main Screen.

IMPORTANT!

iLEARN Door Control Parameters and iDRIVE VFD Door Control Parameters

are not SAVED until the system is restarted - please proceed to SYSTEM RESTART.

2. System Restart

a. Using the MENU/SELECT knob, turn and select DIAGNOSTICS.

b. Select RESTART SYSTEM

c. Turn MENU/SELECT knob to indicate YES and then push to restart your

COURION System.

Boot Screen - During the reboot process, COURION’s iLEARN Door Control

will establish communication with each of your iDRIVE VFD Floor Controls.

The number of iDRIVEs found should equal the number of iDRIVEs expect-

ed.

NOTE

: If there is a discrepancy between the number of iDRIVEs found

and expected,

DO NOT GO TO THE NEXT STEP

. Proceed to the

TROUBLESHOOTING and ERROR MESSAGES

Section of this Manual.

Содержание iDRIVE

































































Результаты поиска

Содержание iDRIVE

Отзывы:

Похожие инструкции для iDRIVE

Бренды по названию

Популярные бренды

Courion iDRIVE, Системное руководство

Результаты поиска

Содержание iDRIVE

Отзывы:

Похожие инструкции для iDRIVE

Бренды по названию

Популярные бренды