background image

Important Information

Page 2

Operation & Maintenance Manual - Vision Chilled Displays

IMPORTANT

Counterline Ltd cannot be held responsible for any accidents or injuries sustained through misuse or improper operation / 
maintenance of its products. Please follow our guidelines set out within this handbook for safe working practice. At the de-
sign stage, please ensure that the counter understructure can take the weight of the display(s), and that adequate provision 
has been made for lifting and positioning the display, to avoid risk of damage or injury. 

SAFETY INFORMATION

It is essential that this Vision unit is provided with an electrical supply by a qualified electrician and 

installed by a competent person.

The presence of liquids on the display and risk of spillage must be taken into account in designing the electrical 

installation around the unit. For additional safety we strongly recommend the fitting of a 30ma trip RCD 

protection device to the electrical supply. 

Under no circumstances should electrical cables or points be installed below 

the evaporator tray area, as water may overflow and cause a hazard. 

Vision display units are heavy. We strongly recommend the use of mechanical lifting equipment when handling the units and 

positioning them in counters. If no such lifting equipment is available then sufficient personnel must be available to handle 

each unit without contravening Company or site Health and Safety Policies.

Before commencing any cleaning or maintenance operation the Vision unit must be isolated from the mains supply by either 
removing the supply plug from its socket or switching off at the local isolator.

NB: Switching off using the power switch on the control panel does not fully isolate the unit. These instructions 
must be implemented in conjunction with your own Company’s Health and Safety instructions.

WARRANTY

All Counterline products are guaranteed against faulty materials and workmanship for 12 months from the date of invoice 
provided that they have been installed, operated, cleaned and maintained in accordance with these instructions.

This guarantee specifically excludes damage caused by misuse, scratched or broken glass, quartz heat lights, fluorescent 

lights and electronic starters.

WARNING

Содержание vision aire
















Отзывы: