Coulomb Technologies ChargePoint CT500-DSTAND Скачать руководство пользователя страница 2

Safety and compliance

This document provides instructions to install the ChargePoint

®

 Charging Station and should not be used for any other product. Before installing 

the ChargePoint

®

 Charging Station, you should review this manual carefully and consult with a licensed contractor, licensed electrician and 

trained installation expert to ensure compliance with local building practices, climate conditions, safety standards, and state and local codes.
The ChargePoint

®

 Charging Station should be installed only by a licensed contractor and a licensed electrician and in accordance with all local 

and national codes and standards. The ChargePoint

®

 Charging Station should be inspected by a qualified installer prior to the initial use. Under 

no circumstances will compliance with the information in this manual relieve the user of his/her responsibility to comply with all applicable codes 
or safety standards. This document describes the most commonly-used installation and mounting scenarios. If situations arise in which it is not 
possible to perform an installation following the procedures provided in this document, contact Coulomb Technologies. Coulomb Technologies is 
not responsible for any damages that may occur resulting from custom installations that are not described in this document. 

No accuracy guarantee

Reasonable effort was made to ensure that the specifications and other information in this manual are accurate and complete at the time of its 
publication. However, the specifications and other information in this manual are subject to change at any time without prior notice.

Warranty information and disclaimer

Your use of, or modification to, the ChargePoint

®

 Charging Station in a manner in which the ChargePoint

®

 Charging Station is not intended to be 

used or modified will void the limited warranty. Other than any such limited warranty, the Coulomb products are provided “AS IS,” and Coulomb 
and its distributors expressly disclaim all implied warranties, including any warranty of design, merchantability, fitness for a particular purposes 
and non-infringement, to the maximum extent permitted by law.

Limitation of liability

IN NO EVENT SHALL COULOMB TECHNOLOGIES, INC. OR ITS AUTHORIZED DISTRIBUTORS BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL, 
PUNITIVE, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST PROFITS, LOST DATA, LOSS OF USE, COST OF COVER, OR LOSS 
OR DAMAGE TO THE CHARGEPOINT

®

 CHARGING STATION, ARISING OUT OF OR RELATING TO THE USE OR INABILITY TO USE THIS MANUAL, EVEN 

IF COULOMB TECHNOLOGIES, INC. OR ITS AUTHORIZED DISTRIBUTORS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Copyright and Trademarks

©2011 Coulomb Technologies, Inc. All rights reserved. This material is protected by the copyright laws of the United States and other countries. It 
may not be modified, reproduced or distributed without the prior, express written consent of Coulomb Technologies, Inc. CHARGEPOINT is a U.S. 
registered trademark and service mark of Coulomb Technologies, Inc. All other products or services mentioned are the trademarks, service 
marks, registered trademarks or registered service marks of their respective owners. Coulomb Technologies has filed several patent applications.

Содержание ChargePoint CT500-DSTAND



























Отзывы: