20
21
Attach the microwave oven
to the top cabinet.
B6.
FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE
RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN.
5
Cabinet Front
Cabinet Bottom Shelf
Tighten the outer two screws to the top of
the microwave oven. (While tightening
screws, hold the microwave oven in place
against the wall and the top cabinet.)
Filler Block
Microwave Oven Top
Equivalent
to Depth
of Cabinet
Recess
Insert 2 self-aligning screws
through outer top cabinet holes.
Turn two full turns on each screw.
Self-Aligning Screw
4
Install grease filters. See the
Use & Care Guide that came
with the microwave for more
information.
4
3
ATTACH THE MOUNTING PLATE TO
THE WALL
1
Wall
Mounting
Plate
Spacing for Toggles
More Than Wall
Thickness
Bolt End
Toggle
Bolt
Toggle Wings
To use toggle bolts:
2
C
RECIRCULATING
(non vented ductless)
Cabinet Cabinet
If the cabinet depth including the cabinet doors
is more than 13", then the unit must be spaced
out from wall using adequate materials supporting
150 Ibs to allow proper top vent air exhaust/intake.
IMPORTANT: Do not grip or use the handle or heat shield during in-
stallation. Do not remove the cardboard spacers between the heat
shield and door.
NOTE: If your cabinet is metal, use the nylon grommet around the
power cord hole to prevent cutting of the cord.
NOTE: We recommend using filler blocks of the cabinet front hangs
below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not used, case damage may occur
from over tightening screws.
NOTE: When mounting the microwave oven, thread power cord
through hole in bottom of top cabinet. Keep it tight throughout
steps 1-3. Do not pinch cord or lift oven by pulling cord.
Lift microwave, tilt it forward, and hook slots at
back bottom edge onto four lower tabs of mount-
ing plate.
1
2
Rotate front of oven
up against bottom.
3
Insert self-aligning screw through top center cabi-
net hole. Temporarily secure the oven by turning
the screw at least two full turns after the threads
have engaged (it will be completely tightened
later). Be sure to keep the power cord tight. Be
careful not to pinch the cord, especially when
mounting flush to bottom of cabinet.
6
INSTALLATION OVERVIEW
C1. Attach Mounting Plate to Wall
C2. Prepare Top Cabinet
C3. Check Blower Plate
C4. Mount the Microwave Oven
C5. Install or change Charcoal Filter
IMPORTANT NOTES
• Make sure the screws for the blower motor and
blower plate are securely tightened when they are
reinstalled. This will help prevent excessive vibration.
•Make sure the motor wiring has been properly
routed and secured and that the wires are not
pinched.
C1
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
Remove the toggle wings from the bolts.
Insert the bolts into the mounting plate through the
holes designated to go into drywall and reattach
the toggle wings 3/4" to (19mm) onto each bolt.
7
Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall to
mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the bottom of the mounting plate
touch the bottom of the cabinet when pushed flush against
the wall and that the plate is properly
centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
Tighten all bolts. Pull the plate away from the wall to
help tighten the bolts.
12"
4"
NO T E :IT IS VER Y IM
P OR TA NT TO
R EAD AN D F O LL O W
T H E DIRE CTI O NS
IN T H E INS T ALL AT I
ON INS TR U CTI O N S
B E F O R E PR O C EE D I
NG W ITH T HIS
R E AR W A LL TE M P LA
T E .
T his R ear W allT emp lat
e serves to position the
bottom
mo unting plate and to lo
cate the horizontal exha
ust
outlet.
1.Us e a levelto check
that the tem plate is posi
ti
oned
accurately.
2. Locate and ma rk atle
ast one stud on the left o
r
right side ofthe centerli
ne.
Itisim portant to use at
leastone w ood
screw mo unted firm ly in
a stud to support the we
ight
of the m icrow ave.Ma rk
two add itional,evenlysp
aced
locations for the supplie
d toggle bolts.
3. Drill holes in the m arke
d locations.Wh ere ther
e is
a stud,drilla 3/16" hole
for w ood screws . For ho
les
thatdo notli
ne up with a stud, dril
l5/8" holes for
toggle bolt
s.
DO N O T IN S T A LL TH E
M OU N TIN G P LA TE
A T T HIS T IM E .
4. Re m ove the tem plate
from the rear w all.
5. Review the Installation
Instruction book for your
installa
tion situation.
Loc ate and m ark hole
s to align with holes i
n the
mount ing plate.
IM PORT ANT:
LOCA T E AT LE AST O
NE STUD O N EIT H E R
SIDE O F
T H E CE N T E R LIN E .
MARK T HE LO CA T IO
N F O R 2 ADDI TIO N A
L, EV EN LY
SPACE D TO G GLE B
O LT S IN TH E MO U N
T ING P LAT E
A R EA .
Locate and mark ho le
s to align with holes i
nthe
m oun ting plate.
IM P O R T A NT :
LO C A T E AT LE A ST O
NE ST U D ON E IT H E
R SIDE O F
T H E CE NT E R LIN E.
M A RK T H E LOCA TIO
N F O R 2 A D DIT ION A
L , EVENL Y
SP A CED TO G G LE BO
LT S IN T H E MO UNT I
N G PLA T E
A RE A.
T rim the rear wall t
em p late alo n g th e d o
tted lin e.
D arle vue lta a la ho ja
para con su ltar la
versión en Es p año l.
3/8" TO EDG E
Trim the rear wall tem
plate along th e dott
ed lin
e.
MOUNT THE MICROWAVE OVEN
B. Outside Back Exhaust (Horizontal Duct)
