¿
-G (PLA300F, PLA600F)
-
Option -G units are low leakage current type.
-
Differences from standard versions are summarized in Table 5.1.
Table 5.1 Low leakage current type
Leakage Current
(AC240V 60Hz)
0.15mA max
Conducted Noise
N/A
Output Ripple Noise
Please contact us for details about
Ripple Noise
*
This is the value that measured on measuring board with capaci-
tor of 22
μ
F and 0.1
μ
F at 150mm from output terminal block.
Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent
to KEISOKU-GIKEN:RM-103).
¿
-V (PLA300F, PLA600F)
-
Option -V units have a connector for external potentiometer in-
stead of a built-in potentiometer.
-
Appearance of Option -V units is different from that of standard
units. Please contact us for details.
-
If power is turned on while CN3 is open, output voltage de-
creases signifi cantly.
CN3
V.ADJ
+V
+V
Fig.5.1 Front view of option-V (PLA600F)
¿
-U (PLA300F, PLA600F)
-
Operation stop voltage of Option -U units is set at a lower value
than that of a standard version to support low input voltage.
-
Use Conditions (Conditions of SEMI F-47 compliant)
Maximum output power
*
( ) is 5V output model.
PLA300F
120W (100W)
PLA600F
240W (200W)
Input AC50V
Duty 1s/30s
*
Please avoid using continuously for more than 1 second under
above conditions. Doing so may cause a failure.
¿
-R (PLA100F, PLA150F, PLA300F, PLA600F)
-
You can control output ON/OFF in Option -R units. An external
DC power supply is connected and it should be applied a volt-
age to a remote ON/OFF connector to control it.
-
Appearance is changed from standard model.
-
There is a lineup of optional harnesses. Refer to option parts.
-
Please contact us for details.
Table 5.2 Remote on/off operating conditions
Model Name
Built-in
Resistor
Ri [
W
]
Voltage between RC
and RCG [V]
Input
Current
[mA]
Output ON Output OFF
PLA100F, PLA150F,
PLA300F, PLA600F
780
4.5 - 12.5
0 - 0.5
(20max)
Ri
RCG
RC
*
1
R
SW
External Power
Source
Remote ON/OFF connector (Optional)
Input Current
Inside of a Power
Supply
Fig.5.2 Example of using a remote ON/OFF circuit
*
1 If the output of an external power supply is within the range
of 4.5 - 12.5V, you do not need a current limiting resistor R. If
the output exceeds 12.5V, however, please connect the cur-
rent limiting resistor R.
To calculate a current limiting resistance value, please use the fol-
lowing equation.
R[
W
]=
Vcc-(1.1+Ri
X
0.005)
0.005
Vcc : External Power Source
*
Please wire carefully. If you wire wrongly, the internal
components of a unit may be damaged.
*
Remote ON/OFF circuits is isolated from input, output and FG
circuits .
¡
PLA100F, PLA150F, PLA300F Remote on/off control.
-
Connector is added. Please contact us for detail.
-
Start up time will be delay when on/off term is very short.
Please keep 2 seconds for on/off cycle.
CN4
Fig.5.3 Example of option -R (PLA100F, PLA150F)
AC-DC Power Supplies Enclosed type
Instruction Manual
PLA-17
PLA
me̲pla1.indd PLA-17
me pla1 indd PLA-17
2014/03/04 10:34:44
2014/03/04 10:34:44
