background image

- 10 - 

 

WARM-UP and COOL-DOWN 

 

Using your machine will provide you with several benefits. It will improve your physical fitness, tone 
your muscles and in conjunction with a calorie-controlled diet, help you lose weight.

 

WARM-UP PHASE 

The purpose of warming up is to prepare your body for exercise and to minimize injuries. Warm up 
for two to five minutes before strength-training or aerobic exercising. Perform activities that raise 
your heart rate and warm the working muscles. Activities may include brisk walking, jogging, 
jumping jacks, jump rope, and running in place. 

STRETCHING 

Stretching while your muscles are warm after a proper warm-up and again after your strength or 
aerobic training session is very important. Muscles stretch more easily at these times because of 
their elevated temperature, which greatly reduces the risk of injury. Stretches should be held for 15 
to 30 seconds. 

DO NOT BOUNCE.

 

Remember always to check with your physician before starting any exercise program. 

 

EXERCISE PHASE 

This is the stage where you put the 
effort in. After regular use, the 
muscles in your legs will become 
more flexible. Work at your own 
pace and be sure to maintain a 
steady tempo throughout. The rate 
of work should be sufficient to raise 
your heartbeat into the target zone 
shown on the graph below. 

 

COOL-DOWN PHASE 

The purpose of cooling down is to return the body to its normal or near normal, resting state at the 
end of each exercise session. A proper cool-down slowly lowers your heart rate and allows blood to 
return to the heart. 

Содержание Omega LGP-10












Отзывы: