background image

Instruction Manual   |   17

 13.  Limited  Warranty

Corning Incorporated (Corning) warrants that this product 

will be free from defects in material and workmanship 

for a period of three (3) years from date of purchase. 

CORNING DISCLAIMS ALL OTHER WARRANTIES 

WHETHER EXPRESSED OR IMPLIED, INCLUDING ANY 

IMPLIED WARRANTIES OF MERCHANTABILITY OR OF 

FITNESS FOR A PARTICULAR PURPOSE. Corning’s sole 

obligation shall be to repair or replace, at its option, any 

product or part thereof that proves defective in material 

or workmanship within the warranty period, provided the 

purchaser notifies Corning of any such defect. Corning is 

not liable for any incidental or consequential damages, 

commercial loss, or any other damages from the use of 

this product. 
This warranty is valid only if the product is used for its 

intended purpose and within the guidelines specified 

in the supplied instruction manual. This warranty does 

not cover damage caused by accident, neglect, misuse, 

improper service, natural forces, or other causes not 

arising from defects in original material or workmanship. 

This warranty does not cover the PTFE seal, O-ring, or 

shaft. Claims for transit damage should be filed with the 

transportation carrier.
In the event this product fails within the specified period 

of time because of a defect in material or workmanship, 

contact Corning Customer Service at: USA/Canada 

1.800.492.1110, outside the U.S. +1.978.442.2200, visit  

www.corning.com/lifesciences

, or contact your local 

support office. 
Corning Customer Service will help arrange local service 

where available or coordinate a return authorization 

number and shipping instructions. Products received 

without proper authorization will be returned. All items 

returned for service should be sent postage prepaid in 

the original packaging or other suitable carton, padded to 

avoid damage. Corning will not be responsible for damage 

incurred by improper packaging. Corning may elect for 

onsite service for larger equipment. 
Some states do not allow limitation on the length of 

implied warranties or the exclusion or limitation of 

incidental or consequential damages. This warranty gives 

you specific legal rights. You may have other rights which 

vary from state to state. 

Содержание Lambda Plus






















Отзывы: