background image

 

© 

2017, Cornelius Inc.                                                                

- 1 -

   

 

Important

:

 

This manual contains important information. Please be sure to read and understand this 
manual before installation, operation and servicing. 

Users of the device are expected to be 

familiar  with  or  trained  on  electronics,  pipes,  pneumatics,  refrigeration  and  mechanical 
equipment.  Operations must comply with safety specifications and meet local requirements 
for safety and operations, and all wiring and piping installation must comply with national and 
local codes. Failure to comply with these specifications and codes will likely lead to serious 
personal injury, death or damage to the device. 

 
 

Contact us: 

The product and technical information and explanations contained herein are not intended to 
cover all details or variations of the device, nor to provide for every possible contingency in 
installation, operation or maintenance of this device. These explanations are subject to change 
without notice from time to time. To familiarize yourself with the latest versions of this manual 
or other documents, or should you need technical supports for any Cornelius product, please 
contact local supporting technicians of Cornelius or obtain assistance through:   

CORNELIUS INC, 12 Xin Tai Road, TEDA, Tianjin, PRC, 300457

 

www.cornelius.com.cn 
+86-22-2529-0858 
[email protected] 

 
 
 

Trademark and copyright: 

This document contains ownership and proprietary information and may not be reproduced 
in any way without written consent from Cornelius. 

 

 
 
 
 
 
 
 
 
 
 

 

Содержание Cascata180





















Отзывы: