manualshive.com logo in svg

Coretec VCX-7401, Инструкция по установке и эксплуатации

Поделиться
Скачать
Coretec VCX-7401 Скачать руководство пользователя страница 22

Reboot Button

The reboot button will immediately shut down the device and reboot. If any 
changes were made during the session and not commited, then they will not stay 
in effect after reboot completes. 

NOTE: This is good to use if the user has made many new configurations but 
doesn't wish to keep them.

Open Manual

The open manual button is just a shorcut to open this manual.

View H264 Video

 

This button will open a new page where the H.264 video stream may be 

viewed.

View MPEG4 Video

This button will open a new page where the MPEG4 video stream may be 

viewed.

4. SNMP

Please refer to SNMP Commands for VCX-7401 Document.

Program Commands

IMPORTANT NOTES:

1. After entering one or more commands, it is necessary to enter COMMIT and REBOOT for 

the new settings to take effect.

2. Typing “?” displays a listing of all commands.
3. The prompt will tell you if commands related to the encoder and decoder are applied to one 

or   the   other.     If   the   prompt   is   “Encoder>”   then   the   command   applies   to   the   encoder. 
Likewise, if the prompt is “Decoder>” then the commans applies to the decoder.  The current  
mode can be changed by typing MPEG4, H264 or DECODER at the prompt.

22

Содержание VCX-7401







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды