Copystar CS 181 Скачать руководство пользователя страница 93

Страница: 93 / 355

2KJ/2KH

1-3-53

U402

Adjusting margins of image printing
Description

Adjusts margins for image printing.

Purpose

Make the adjustment if margins are incorrect.

Adjustment

1. Press the start key.
2. Select the item to be adjusted using the cursor up/down keys.

3. Press the interrupt key.
4. Press the start key to output a test pattern.
5. Change the setting value using the cursor left/right keys.

Increasing the value makes the margin wider, and decreasing it makes the margin narrower.

Figure 1-3-17

6. Press the start key. The value is set.

Caution

Check the copy image after the adjustment. If the image is still incorrect, perform the following adjustments in
maintenance mode.

Completion

Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Display

Description

Setting
range

Initial
setting

Change in
value per step

LEAD

Printer leading edge margin

0 to 10.0

3.0

0.1 mm

Printer left and right margin

-3.4 to 10.0

3.0

0.1 mm

TRAIL

Printer trailing edge margin

-5.0 to 10.0

4.0

0.1 mm

Printer leading edge margin
(3.0±1.0 mm)

Printer

left margin

Printer
right margin

Printer trailing edge margin
(3.0±1.0 mm)

(2.5±1.0 mm)

U402

U403

(P.1-3-54)

U404

(P.1-3-55)

Содержание CS 181




































































































































































































































































































































































Результаты поиска

Содержание CS 181

Отзывы:

Бренды по названию

Популярные бренды

Copystar CS 181, Руководство по обслуживанию

Результаты поиска

Содержание CS 181

Отзывы:

Бренды по названию

Популярные бренды