manualshive.com logo in svg

Copystar CS 181, Руководство по обслуживанию

Поделиться
Скачать
Copystar CS 181 Скачать руководство пользователя страница 115

2KJ/2KH

1-4-1

1-4 Troubleshooting

1-4-1  Paper misfeed detection

(1) Paper misfeed indication

When a paper misfeed occurs, the machine immediately stops copying and displays the jam location on the operation
panel.
Paper misfeed counts sorted by the detection condition can be checked in maintenance item U903.
To remove paper jammed in the machine, open the front cover, left cover or pull the cassette out.
To remove original jammed in the optional DP, open the document processor top cover.
To remove the jammed paper in optional document finisher, detach the finisher from the machine.
Paper misfeed detection can be reset by opening and closing the respective covers to turn safety switch off and on.

Figure 1-4-1

1

5

6

7

8

2

3

4

1

2

3

4

(1)

Misfeed in cassette

(2)

Misfeed in first paper feeder

(3)

Misfeed in second paper feeder

(4)

Misfeed in third paper feeder

(5)

Misfeed in MP tray

(6)

Misfeed in paper conveying section

(7)

Misfeed in eject section

 (job separator or built-in finisher)

(8)

Misfeed in document processor

Содержание CS 181




































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды