manualshive.com logo in svg

Copystar CS 181, Руководство по обслуживанию

Поделиться
Скачать
Copystar CS 181 Скачать руководство пользователя страница 65

2KJ/2KH

1-3-25

U072

Adjusting the DP center line
Description

Adjusts the scanning start position for the DP original.

Purpose

Make the adjustment if there is a regular error between the centers of the original and the copy image when 
the optional DP is used.

Adjustment

1. Press the start key.
2. Select the item to be adjusted using the cursor up/down keys.

3. Press the interrupt key.
4. Place an original on the DP and press the start key to make a test copy.
5. Change the setting value using the cursor left/right keys.

For copy example 1, increase the value. For copy example 2, decrease the value.

Figure 1-3-13

6. Press the start key. The value is set.

Caution

Check the copy image after the adjustment. If the image is still incorrect, perform the following adjustments in 
maintenance mode.

Completion

Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Display

Description

Setting
range

Initial
setting

Change in
value per step

1sided

DP center line (simplex mode)

-39 to 39

0

0.15 mm

2sided front

DP center line (first page of duplex 
mode)

-39 to 39

0

0.15 mm

2sided back

DP center line (second page of 
duplex mode)

-39 to 39

0

0.15 mm

Original

Copy

example 1

Copy

example 2

U072

U404

(P.1-3-55)

Содержание CS 181




































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды