manualshive.com logo in svg

Copystar CS 181, Руководство по обслуживанию

Поделиться
Скачать
Copystar CS 181 Скачать руководство пользователя страница 62

2KJ/2KH

1-3-22

U070

Adjusting the DP magnification
Description

Adjusts the DP original scanning speed.

Purpose

Make the adjustment if the magnification is incorrect in the auxiliary scanning direction when the optional DP 
is used.

Adjustment

1. Press the start key.
2. Select the item to be adjusted using the cursor up/down keys.

1. Press the interrupt key.
2. Place an original on the DP and press the start key to make a test copy.
3. Change the setting value using the cursor left/right keys.

For copy example 1, increase the value. For copy example 2, decrease the value.

Figure 1-3-10

4. Press the start key. The value is set.

Caution

Check the copy image after the adjustment. If the image is still incorrect, perform the following adjustments in 
maintenance mode.

Completion

Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Display

Description

Setting
range

Initial
setting

Change in
value per step

CONVEY 
SPEED 1

Magnification in the auxiliary scan-
ning direction (first page)

-25 to 25

0

0.2 mm

CONVEY 
SPEED 2

Magnification in the auxiliary scan-
ning direction (second page)

-25 to 25

0

0.2 mm

Original

Copy

example 1

Copy

example 2

U070

U071

(P.1-3-23)

U404

(P.1-3-55)

Содержание CS 181




































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды