Cooper Power Systems Kyle Type ME Series Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 50

Cooper Power Systems Kyle Type ME Series Скачать руководство пользователя страница 7

S280-75-2

7

Figure 7.
View of a Form 3A tie board (back if front panel. Notations in parenthesis after callout refer to the circuit points on the tie board dia-
gram illustrated in Figure 57.

88939KMA

7. Check battery voltage. Three battery test terminals in the

lower right corner of the panel (Figure 2) are used to check
battery voltage, quiescent drain, and charging rate. Refer
to the “Battery Maintenance” instructions in this manual.

The left-hand pair of terminals (V) are connected directly

across the battery output to check battery voltage. The red
terminal (far left) is positive (+). The output voltage of a fully
charged battery will normally be 26-28-volts. If lower, refer

to the “Detailed Circuit check—Battery Charging” and/or
“Battery Maintenance” section of this manual.

If necessary, recharge the battery, as detailed in the

“Battery Maintenance” section.

8. Make sure circuit boards are secure in their receptacles.

Examine wiring between transformers and tie boards to see if
connections are in order. Close front panel and secure firmly
with fasteners.

«
...
5
6
7
8
9
...
»

Содержание Kyle Type ME Series



















































Отзывы:

Нет отзывов