manualshive.com logo in svg

Cooper Bussmann 945U-E, Руководство пользователя, Страница: 54 / 109

Поделиться
Скачать
Cooper Bussmann 945U-E Скачать руководство пользователя страница 54

54

www.cooperbussmann.com/wirelessresources

Cooper Bussmann 945U-E Wireless Ethernet Modem & Device Server User Manual

Rev Version 2.14

Example 2: Roaming with WDS Access Points

Figure 48  WDS Roaming

Another common use for WDS is extending the range across a large wireless network by allowing roaming 
connections between access points or being able to switch to the next access point when out of range of the 
previous access point. Figure 48 shows a bridging network with a number of access points all with the same SSID 
and network structure, so the Stations can freely roam between access points.

Each access point then needs a separate connection to the next access point, which is provided using the WDS 
Virtual Access Points and Stations. Site B is acting as a virtual AP for Site A, which in turn is acting as a virtual 
station. At the same time Site B is also acting as a virtual station for Site C which in turn is acting as a virtual 
access point. This setup can be replicated to extend the range and will allow any roaming stations full connectivity 
across the network.

Figure 49  Site B WDS Configuration 2

Example 3: Adding Redundancy

In the example below, 4 x access points (A, B, C, & D) form a mesh network using only WDS bridge interfaces. 
Each of the access points may also have its own associated clients. Each access point is configured with a 
different SSID, which means that the clients associated with each access point are fixed.

Содержание 945U-E














































































































Отзывы:

Нет отзывов