Cooper & Hunter Arctic NG Wi-Fi Series, Руководство пользователя

Страница: 19 / 111

18
For preventing cold air, after starting up heat mode,
indoor unit will delay 1~5 minutes to blow air (Actual
delay time depends on indoor ambient temperature).
Set temperature range from remote controller:
16~30
℃ (61-86 ℉ ).
This mode indicator is not available for some models.
Cooling only unit won't receive heat mode signal. If
setting heat mode with remote controller, press
" "
button can't start up the unit.
●
●
●
●
button
button
button
●
●
This is a general use remote controller. It could be
used for the air conditioner with multifunction. For the
functions which the model doesn't have, if press the
corresponding button on the remote controller, the
unit will keep the original running status.
After putting through the power, the air conditioner
will give out a sound. Power indicator " " is ON.
After that, you can operate the air conditioner by
using remote controller.
Under on status, pressing the button on the remote
controller, the signal icon " " on the display of
remote controller will blink once and the air condition
-
er will give out a " di " sound, which means the signal
has been sent to the air conditioner.
Press this button to turn on the unit. Press this button
again to turn off the unit.
AUTO
COOL DRY
FAN HEAT
When selecting auto mode, air conditioner will
operate automatically according to the sensed
temperature. Set temperature can't be adjusted
and will not be displayed as well. Press "FAN"
button can adjust fan speed. Press " " / " "
button can adjust fan blowing angle.
After selecting cool mode, air conditioner will
operate under cool mode. Press "▲" or "▼"
button to adjust set temperature. Press "FAN"
button to adjust fan speed. Press " " / " "
button to adjust fan blowing angle.
When selecting dry mode, the air conditioner
operates at low speed under dry mode. Under
dry mode, fan speed can't be adjusted.
Press " " / " " button to adjust fan blowing
angle.
When selecting fan mode, the air conditioner will
only blow fan, no cooling and no heating. Press
"FAN" button to adjust fan speed. Press " " /
Press this button to select your required operation
mode.
●
●
●
●
" " button to adjust fan blowing angle.
When selecting heat mode, the air conditioner
operates under heat mode. Press "▲" or "▼"
button to adjust set temperature. Press "FAN"
button to adjust fan speed. Press " " / " "
button to adjust fan blowing angle.
●
This button is used for setting Fan Speed in the se-
quence that goes from AUTO, , , ,
to , then back to Auto.
●
NOTE
NOTE
Introduction for buttons on
remote controller
Low-Medium speed Medium speed
It's low fan speed under dry mode.
X-FAN function Hold fan speed button for 2s in cool
or dry mode, the icon " " is displayed and the in-
door fan will continue operation for a few minutes in
order to dry the indoor unit even though you have turn-
ed off the unit. After energization, X-FAN OFF is
defaulted. X-FAN is not available in auto, fan or heat
mode.
This function indicates that moisture on evaporator of
indoor unit will be blowed after the unit is stopped to
avoid mould.
Having set X-FAN function on: After turning off the
unit by pressing " " button indoor fan will continue
running for a few minutes. at low speed. In this per-
iod, Hold fan speed button for 2s to stop indoor fan
directly.
Having set X-FAN function off: After turning off the
unit by pressing " " button, the complete unit will
be off directly.
●
●
●
●
NOTE
Auto
Low speed
Medium-High speed High speed
19
button
button
button
button
Under cool or heat mode, press this button to turn
to quick cool or quick heat mode. " " icon is
displayed on remote controller. Press this button
again to exit turbo function and " " icon will
disappear.
If start this function, the unit will run at super-high
fan speed to cool or heat quickly so that the ambi -
ent temperature approaches the preset tempera -
ture as soon as possible.
Press this button can select left & right swing angle.
Fan blow angle can be selected circularly as below:
●
●
●
●
Press "▲" or "▼" button once increase or dec-
rease set temperature 1°C(°F). Holding "▲" or "▼"
button, 2s later, set temperature on remote control-
ler will change quickly. On releasing button after
setting is finished, temperature indicator on indoor
unit will change accordingly. (Temperature can't be
adjusted under auto mode)
When setting TIMER ON, TIMER OFF or CLOCK,
press "▲" or "▼" button to adjust time. (Refer to
CLOCK, TIMER ON, TIMER OFF buttons).
" " may not be available. When air condi -
tioner receives this signal, the air conditioner will blow
fan automatically.
Press this button continuously for more than 2s, the
main unit will swing back and forth from up to down,
and then loosen the button, the unit present position
of guide louver will be kept immediately.
Under up and down swing mode, when the status is
switched from off to , if press this button again 2s
later, status will switch to off status directly; if
press this button again within 2s, the change of swing
status will also depend on the circulation sequence
stated above.
●
●
●
、 、
When selecting " ", air conditioner is blowing
fan automatically. Horizontal louver will automat -
ically swing up & down at maximum angle.
When selecting " ", air condition -
er is blowing fan at fixed position. Horizontal
louver will stop at the fixed position.
When selecting " ", air conditioner is
blowing fan at fixed angle. Horizontal louver will
send air at the fixed angle.
Hold " "button above 2s to set your required
swing angle. When reaching your required
angle, release the button.
no display
(horizontal louvers
stops at current position)
、 、 、 、
、 、
Press this button, can select Sleep 1 ( ), Sleep 2
( ), Sleep 3 ( ) and cancel the Sleep, circulate
between these, after electrified, Sleep Cancel is de-
faulted.
button
Press this button can select up & down swing angle.
Fan blow angle can be selected circularly as below:
NOTE
NOTE
no display
(st ops a t
current po
si
tion)
●
●
Press this button continuously more than 2s, the main
unit will swing back and forth from left to right, and
then loosen the button, the unit will stop swinging and
present position of guide louver will be kept immedi
-
ately.
Under left and right swing mode, when the status is
switched from off to , if press this button again
2s later, status will switch to off status directly; if
press this button again within 2s, the change of swing
status will also depend on the circulation sequence stat-
ed above.
The function is only available for some models.
●
Sleep 1 is Sleep mode 1, in Cool modes; sleep sta-
tus after run for one hour, the main unit setting tem-
perature will increase 1 , two hours, setting temper-
ature increased 2 , then the unit will run at this set-
ting temperature; In Heat mode: sleep status after
run for one hour, the setting temperature will de-
crease 1 , two hours, setting temperature will de-
crease 2 , then the unit will run at this setting tem-
perature.
Sleep 2 is sleep mode 2, that is air conditioner will
run according to the presetting a group of sleep tem-
perature curve.
●
●