Coolmay EX3G-100HA Скачать руководство пользователя страница 62

Страница: 62 / 72

COOLMAY EX3G PLC/HMI All in one Programming manual

Auxiliary

[M0~M499] 500 points General;

[M500~M1535] 1036 points Keep in;

[M8000~M8255] 256 points Special.

[M0~M383] 384 points General;

[M384~M1535] 1152 points to keep in;

[M1536

～

M7679] 6144 points General;

[M8000

～

M8511] 512 points Special.

Data register

range

[D0~D199] 200 points General;

[D200~D999] 800 points Keep in ;

[D8000-D8255] 256 points Special.

[D0~D127] 128 points General;

[D128~D7999] 7872 points to keep in;

File register [R0~R23999] 24000 points to

keep;

[D8000-D8511] 512 points Special.

Status register

range

[S0~S9] 10 points Initial status;

[S10~S499] 490 points General;

[S500~S999] 500 points keep in.

[S0-S9] 10 points for initial state;

[S10~S999] 990 points to keep in use;

[S1000~S4095] 3096 points Generally used.

Timer range

[T0~T199] 200 points 100ms General;
[T200~T245] 46 points 10ms General;

[T246~249] 4 points 1ms, General;

[T250~T255] 6 points 100ms Cumulative keep

in.

[T0~T199] 200 points 100ms is general;

[ T200~T245] 46 points 10ms for general use;

[T246~T249] 4 points 1ms cumulatively

used;

[T250~T255] 6 points 100ms cumulatively

used;

[T256~T319] 64 points 1ms Normal use.

Counter range

[C0~C99] 100 points Generally 16 bits;

[C100~C199] 100 points Power outage

remains 16 bits; [C200~C234] 35 points Power

outage remains 32 bits.

[C0~C15] 16 points, generally 16 bits;

[C16~C199] 184 points, power failure to

maintain 16 places;

[C200~C219] 20 points, generally 32 bits;

[C220~C234] 15 points Power failure to

maintain 32 bits.

Pointer,

interrupt

[P0~P127] 128 points JUMP CALL.

[P0~P255] 256 points JUMP CALL;

[P0~P1280] 1281 points JUMP CALL (26232

and above);

Input interrupt 6 points I0□□~I5□□;

The timer is interrupted by 3 points

I6□□~I8□□.

DI/DO

Up to 24DI/20DO, at most 18 relay can be

available.

Supports up to 30DI/30DO and up to 28 MR.

Note: When the switch quantity reaches

30DI/30DO, the analog quantity can be up to

5AD/2DA; when the switch quantity is

24DI/20 DO, the analog quantity can be up to

16AD/ 8DA.

DO type and

load

Relay MR(Maximum load: 5A)/Transistor

MT(Maximum load:500mA)/Mixed output MRT.

EX3G-43H/HB/EX3G-43(50)KH series

optional

Relay MR (maximum load 5A) / MOS tube

(maximum load 2A)

EX3G-70KH/100HA optional relay MR

(maximum load 5A) /

Transistor MT (maximum load 500mA) /

Содержание EX3G-100HA









































































Результаты поиска

Содержание EX3G-100HA

Отзывы:

Бренды по названию

Популярные бренды

Coolmay EX3G-100HA, Руководство по программированию

Результаты поиска

Содержание EX3G-100HA

Отзывы:

Бренды по названию

Популярные бренды