POWERING UP YOUR SOLAR
POWERED SOLAR SHADE (continued)
IMPORTANT:
• Do not recharge other battery types besides those provided
for the Autosun system (rechargeable NiMh
• 12V - 2.2Ah battery - réf.9014734), there is a risk of explosion.
• Keep away (1m minimum) from from all types of flames,
sparks or incandescent material.
• Do not open the charger, risk of electric shock.
• Do not use the charger if the cable is damaged.
• Do not cover during use.
• Maximum charging time for 1 battery: 210 min.
• 2 charges / year max.
• Minimum charging time to be able to open the shade (with a
battery in good condition): 20 minutes.
A. Connect the charger
(sold separately)
to the main supply. The
two-colour LED (green / red) lights up green, the charger is ready
to use.
B. Disconnect the battery from the motor.
C. Connect the charger to the battery cable. The LED changes
colour from green to red.
D. Charging is finished when the LED changes colour back to
green. Disconnect the charger from the battery.
E. Reconnect the battery to the motor.
Your solar powered shade is now ready for use.
NOTE:
If the battery is fully discharged due to lack of sun, solar
panel was covered, etc., you can place the solar panel in direct sun
for several hours a day. If the charge doesn’t happen, you may
need to purchase a charger via our website,
www.coolaroo.com
,
or contact customer service at
1-800-560-4667
.
12
- Press the “PROG” key of the battery pack more than 7 seconds. The motor will run 2 times
for in one direction and then in the other. The operation is completed.
The motor doesn't have any transmitter programmed in its memory any more, but
the settings for the direction of rotation and end limits are retained. Perform opera-
tion 2.1c then operation 3 to programme a new individual controller.
7s
2s
5s
8. Cancelling all the programmed transmitters
- Press the “PROG” key of the battery pack more than 12 seconds. The motor will
run 3 times in one direction and then in the other. The operation is completed.
The motor returns to its original set up, with no transmitter programmed
in the memory. Redo the complete programming procedure for the motor
(direction of rotation, end limits and control points).
Before each lifting or lowering of the shutter, the motor checks the voltage of the battery.
If the voltage is below 11.5V: The motor will pause at the beginning of each command to lift the shutter. The shutter can
only be closed by pressing several times on the "down" button.
If the voltage is below 10V: The receiver won’t accept any commands.
12s
2s
7s
12s
9. Complete cancelling of programming
10. Battery protection against excessive discharge
11. Battery pack replacement
In these two cases, use the emergency charger in order to perform a quick battery recharge. Operation of the
motor will return to normal only if the battery voltage goes above 12V.
1
LED
1
1
2
2
3
4
5
210 min.
6
7
1-
Connect the charger to the mains supply. The two-colour LED (green / red) lights up
green
, the charger is ready to use.
2-
Open the battery cover.
3-
Disconnect the battery from the motor.
4-
Connect the charger to the battery. The LED changes colour from
green to red
.
5-
Charging is finished when the LED changes colour back to
green
. Disconnect the charger from the battery and from the mains.
6-
Reconnect the battery to the motor.
7-
Replace the battery cover.
1-
Disconnect the battery pack, the motor
(a)
and the solar panel
(b)
2-
Replace the battery pack
(c)
.
with an identical model
.
3-
Charge the new pack. Connect the new pack to the motor and the solar panel.
- Do not recharge other battery types besides those provided for the Autosun system (rechargeable NiMh 12V - 2.2Ah
battery - réf.9014734), there is a risk of explosion.
- Keep away (1m minimum) from from all types of flames, sparks or incandescent material.
- Do not open the charger, risk of electric shock.
- Do not use the charger if the cable is damaged.
- Do not cover during use.
- Maximum charging time for 1 battery:
3 hours 30 min.
- 2 charges / year max.
- Minimum charging time to be able to open the shutter (with a battery in good condition): 20 minutes.
c
a
b
Fig. 1
12
- Press the “PROG” key of the battery pack more than 7 seconds. The motor will run 2 times
for in one direction and then in the other. The operation is completed.
The motor doesn't have any transmitter programmed in its memory any more, but
the settings for the direction of rotation and end limits are retained. Perform opera-
tion 2.1c then operation 3 to programme a new individual controller.
7s
2s
5s
8. Cancelling all the programmed transmitters
- Press the “PROG” key of the battery pack more than 12 seconds. The motor will
run 3 times in one direction and then in the other. The operation is completed.
The motor returns to its original set up, with no transmitter programmed
in the memory. Redo the complete programming procedure for the motor
(direction of rotation, end limits and control points).
Before each lifting or lowering of the shutter, the motor checks the voltage of the battery.
If the voltage is below 11.5V: The motor will pause at the beginning of each command to lift the shutter. The shutter can
only be closed by pressing several times on the "down" button.
If the voltage is below 10V: The receiver won’t accept any commands.
12s
2s
7s
12s
9. Complete cancelling of programming
10. Battery protection against excessive discharge
11. Battery pack replacement
In these two cases, use the emergency charger in order to perform a quick battery recharge. Operation of the
motor will return to normal only if the battery voltage goes above 12V.
1
LED
1
1
2
2
3
4
5
210 min.
6
7
1-
Connect the charger to the mains supply. The two-colour LED (green / red) lights up
green
, the charger is ready to use.
2-
Open the battery cover.
3-
Disconnect the battery from the motor.
4-
Connect the charger to the battery. The LED changes colour from
green to red
.
5-
Charging is finished when the LED changes colour back to
green
. Disconnect the charger from the battery and from the mains.
6-
Reconnect the battery to the motor.
7-
Replace the battery cover.
1-
Disconnect the battery pack, the motor
(a)
and the solar panel
(b)
2-
Replace the battery pack
(c)
.
with an identical model
.
3-
Charge the new pack. Connect the new pack to the motor and the solar panel.
- Do not recharge other battery types besides those provided for the Autosun system (rechargeable NiMh 12V - 2.2Ah
battery - réf.9014734), there is a risk of explosion.
- Keep away (1m minimum) from from all types of flames, sparks or incandescent material.
- Do not open the charger, risk of electric shock.
- Do not use the charger if the cable is damaged.
- Do not cover during use.
- Maximum charging time for 1 battery:
3 hours 30 min.
- 2 charges / year max.
- Minimum charging time to be able to open the shutter (with a battery in good condition): 20 minutes.
c
a
b
Fig. 2
12
- Press the “PROG” key of the battery pack more than 7 seconds. The motor will run 2 times
for in one direction and then in the other. The operation is completed.
The motor doesn't have any transmitter programmed in its memory any more, but
the settings for the direction of rotation and end limits are retained. Perform opera-
tion 2.1c then operation 3 to programme a new individual controller.
7s
2s
5s
8. Cancelling all the programmed transmitters
- Press the “PROG” key of the battery pack more than 12 seconds. The motor will
run 3 times in one direction and then in the other. The operation is completed.
The motor returns to its original set up, with no transmitter programmed
in the memory. Redo the complete programming procedure for the motor
(direction of rotation, end limits and control points).
Before each lifting or lowering of the shutter, the motor checks the voltage of the battery.
If the voltage is below 11.5V: The motor will pause at the beginning of each command to lift the shutter. The shutter can
only be closed by pressing several times on the "down" button.
If the voltage is below 10V: The receiver won’t accept any commands.
12s
2s
7s
12s
9. Complete cancelling of programming
10. Battery protection against excessive discharge
11. Battery pack replacement
In these two cases, use the emergency charger in order to perform a quick battery recharge. Operation of the
motor will return to normal only if the battery voltage goes above 12V.
1
LED
1
1
2
2
3
4
5
210 min.
6
7
1-
Connect the charger to the mains supply. The two-colour LED (green / red) lights up
green
, the charger is ready to use.
2-
Open the battery cover.
3-
Disconnect the battery from the motor.
4-
Connect the charger to the battery. The LED changes colour from
green to red
.
5-
Charging is finished when the LED changes colour back to
green
. Disconnect the charger from the battery and from the mains.
6-
Reconnect the battery to the motor.
7-
Replace the battery cover.
1-
Disconnect the battery pack, the motor
(a)
and the solar panel
(b)
2-
Replace the battery pack
(c)
.
with an identical model
.
3-
Charge the new pack. Connect the new pack to the motor and the solar panel.
- Do not recharge other battery types besides those provided for the Autosun system (rechargeable NiMh 12V - 2.2Ah
battery - réf.9014734), there is a risk of explosion.
- Keep away (1m minimum) from from all types of flames, sparks or incandescent material.
- Do not open the charger, risk of electric shock.
- Do not use the charger if the cable is damaged.
- Do not cover during use.
- Maximum charging time for 1 battery:
3 hours 30 min.
- 2 charges / year max.
- Minimum charging time to be able to open the shutter (with a battery in good condition): 20 minutes.
c
a
b
Fig. 3
12
- Press the “PROG” key of the battery pack more than 7 seconds. The motor will run 2 times
for in one direction and then in the other. The operation is completed.
The motor doesn't have any transmitter programmed in its memory any more, but
the settings for the direction of rotation and end limits are retained. Perform opera-
tion 2.1c then operation 3 to programme a new individual controller.
7s
2s
5s
8. Cancelling all the programmed transmitters
- Press the “PROG” key of the battery pack more than 12 seconds. The motor will
run 3 times in one direction and then in the other. The operation is completed.
The motor returns to its original set up, with no transmitter programmed
in the memory. Redo the complete programming procedure for the motor
(direction of rotation, end limits and control points).
Before each lifting or lowering of the shutter, the motor checks the voltage of the battery.
If the voltage is below 11.5V: The motor will pause at the beginning of each command to lift the shutter. The shutter can
only be closed by pressing several times on the "down" button.
If the voltage is below 10V: The receiver won’t accept any commands.
12s
2s
7s
12s
9. Complete cancelling of programming
10. Battery protection against excessive discharge
11. Battery pack replacement
In these two cases, use the emergency charger in order to perform a quick battery recharge. Operation of the
motor will return to normal only if the battery voltage goes above 12V.
1
LED
1
1
2
2
3
4
5
210 min.
6
7
1-
Connect the charger to the mains supply. The two-colour LED (green / red) lights up
green
, the charger is ready to use.
2-
Open the battery cover.
3-
Disconnect the battery from the motor.
4-
Connect the charger to the battery. The LED changes colour from
green to red
.
5-
Charging is finished when the LED changes colour back to
green
. Disconnect the charger from the battery and from the mains.
6-
Reconnect the battery to the motor.
7-
Replace the battery cover.
1-
Disconnect the battery pack, the motor
(a)
and the solar panel
(b)
2-
Replace the battery pack
(c)
.
with an identical model
.
3-
Charge the new pack. Connect the new pack to the motor and the solar panel.
- Do not recharge other battery types besides those provided for the Autosun system (rechargeable NiMh 12V - 2.2Ah
battery - réf.9014734), there is a risk of explosion.
- Keep away (1m minimum) from from all types of flames, sparks or incandescent material.
- Do not open the charger, risk of electric shock.
- Do not use the charger if the cable is damaged.
- Do not cover during use.
- Maximum charging time for 1 battery:
3 hours 30 min.
- 2 charges / year max.
- Minimum charging time to be able to open the shutter (with a battery in good condition): 20 minutes.
c
a
b
Fig. 4
Fig. 5
17
12
- Press the “PROG” key of the battery pack more than 7 seconds. The motor will run 2 times
for in one direction and then in the other. The operation is completed.
The motor doesn't have any transmitter programmed in its memory any more, but
the settings for the direction of rotation and end limits are retained. Perform opera-
tion 2.1c then operation 3 to programme a new individual controller.
7s
2s
5s
8. Cancelling all the programmed transmitters
- Press the “PROG” key of the battery pack more than 12 seconds. The motor will
run 3 times in one direction and then in the other. The operation is completed.
The motor returns to its original set up, with no transmitter programmed
in the memory. Redo the complete programming procedure for the motor
(direction of rotation, end limits and control points).
Before each lifting or lowering of the shutter, the motor checks the voltage of the battery.
If the voltage is below 11.5V: The motor will pause at the beginning of each command to lift the shutter. The shutter can
only be closed by pressing several times on the "down" button.
If the voltage is below 10V: The receiver won’t accept any commands.
12s
2s
7s
12s
9. Complete cancelling of programming
10. Battery protection against excessive discharge
11. Battery pack replacement
In these two cases, use the emergency charger in order to perform a quick battery recharge. Operation of the
motor will return to normal only if the battery voltage goes above 12V.
1
LED
1
1
2
2
3
4
5
210 min.
6
7
1-
Connect the charger to the mains supply. The two-colour LED (green / red) lights up
green
, the charger is ready to use.
2-
Open the battery cover.
3-
Disconnect the battery from the motor.
4-
Connect the charger to the battery. The LED changes colour from
green to red
.
5-
Charging is finished when the LED changes colour back to
green
. Disconnect the charger from the battery and from the mains.
6-
Reconnect the battery to the motor.
7-
Replace the battery cover.
1-
Disconnect the battery pack, the motor
(a)
and the solar panel
(b)
2-
Replace the battery pack
(c)
.
with an identical model
.
3-
Charge the new pack. Connect the new pack to the motor and the solar panel.
- Do not recharge other battery types besides those provided for the Autosun system (rechargeable NiMh 12V - 2.2Ah
battery - réf.9014734), there is a risk of explosion.
- Keep away (1m minimum) from from all types of flames, sparks or incandescent material.
- Do not open the charger, risk of electric shock.
- Do not use the charger if the cable is damaged.
- Do not cover during use.
- Maximum charging time for 1 battery:
3 hours 30 min.
- 2 charges / year max.
- Minimum charging time to be able to open the shutter (with a battery in good condition): 20 minutes.
c
a
b
