15
1
2
503
30
27
Programming button
Connector for charger
The battery pack used in the Autosun solar system has the following functions:
- Store electrical energy provided by the solar panel.
- Supply electrical energy required by the motor.
- Enable programming of the motor using the programming button.
Technical data:
- NiMh battery - 12V / 2,2 Ah
- Battery life: approx. 5 years
- Storage temperature: -20° / +70°C
- Operating temperature: -20° / +70°C
- Storage time: max. 6 months at 20°C
- Protection index: IP X4
- Weight : 0.790 Kg
Presentation
1
NiMh
- Recharge the battery before use with the charger ref.: 9014738. WARNING: Do not charge at a temperature above 70°C.
- Charge duration: 3h 30 min. max. 2 charges by year max.
- Never leave a battery in a discharged condition.
- No not open or pierce the battery.
- Do not put the battery into a fire, risk of explosion. Keep away (1m minimum) from from all types of flames, sparks or incandescent material.
- Do not create a short circuit on the battery terminals: danger of burns and explosion.
- The battery must be sheltered from the rain (IP X4).
- The battery must be accessible in order to carry out possible recharging (see instruction sheet 5055192).
- Suitable substrates for sticking: runners and box in aluminium, box in PVC (remove the protective films).The surfaces to be glued must be dry and clean.
- The ambient temperature when gluing should be between 20°C and 38°C.
- We recommend users run industrial tests in exactly the same conditions as those of the intended application and thereby ascertain that our product satisfies its
requirements. If in doubt, opt for the screwing solution.
- The battery must be replaced by a professional with an identical model.
- Do not put in the dustbin, this is a recyclable product.
- For more information about installation of the battery depending on the type of case, see Technical booklet ref: 5059076
Screw fixing
Glue fixing
- The 2 terminal connector (1) is for connection to the solar panel ref: 9014736
- The 4 terminal connector (2) is for connection to the T3.5 DC EHz motor
Recommendations
2
Mounting
3
Connection of the battery pack
4
1 -
Use solvent* to clean and wipe the surface for
gluing.
2 -
Pass the battery pack cable into the base.
3 -
Remove the protective paper from the adhe-
sive.
4 -
Press the battery pack onto the frame.
* Use a solvent containing a mixture of isopopyl
alcohol and water (50/50) or a heptane-based
solvent. Follow all the safety instructions concer-
ning the handling of solvents.
1
2
3
4
4
1
1
1
1
2
2
478,5
2
18
10
Ø 3mm
GB
BATTERY PACK AUTOSUN - 9014734
S.A.S. au capital de 5 000 000
€
- Z.I. Les Giranaux - BP71 - 70103 Arc-Les-Gray CEDEX - RCS GRAY B 425 650 090 - SIRET 425 650 090 00011 - n° T.V.A CEE FR 87 425 650 090
5055190A
Read carefully these
instructions before any use.
BATTERY MOUNTING OPTIONS
1. PRESENTATION
The battery pack used in the AutoSun™ solar system has the
following functions:
a. Store electrical energy provided by the solar panel.
b. Supply electrical energy required by motor.
Technical Data for battery:
•
NiMh battery - 12V/2.2 Ah
•
Battery life: approx. 5 years
•
Storage temperature: -20 degrees F/+70 degrees C
•
Operating temperature: -20 degrees F/+70 degrees C
•
Storage time: max. 6 months at 20 degrees C
•
Protection index: IP X4
•
Approximate weight: 1.75 lbs.
2. MOUNTING BATTERY PACK WITH TAPE (OPTION 1)
a. Use solvent to clean and wipe the surface for gluing.
b. Pass the battery cable into the base.
c. Remove the protective paper from the adhesive.
d. Press the battery pack into the frame.
NOTE:
Use a solvent containing a mixture of isopopyl alcohol
and water (50/50) or a heptane-based solvent. Follow all the
safety instructions concerning the handling of solvents.
3. MOUNTING THE BATTERY PACK WITH BATTERY
MOUNTING BRACKETS (OPTION 2)
a. Measure brackets for mounting battery.
b. Mount brackets with appropriate hardware to surface.
c. Insert corded end bracket to corded end, insert non corded
end to its bracket.
15
1
2
503
30
27
Programming button
Connector for charger
The battery pack used in the Autosun solar system has the following functions:
- Store electrical energy provided by the solar panel.
- Supply electrical energy required by the motor.
- Enable programming of the motor using the programming button.
Technical data:
- NiMh battery - 12V / 2,2 Ah
- Battery life: approx. 5 years
- Storage temperature: -20° / +70°C
- Operating temperature: -20° / +70°C
- Storage time: max. 6 months at 20°C
- Protection index: IP X4
- Weight : 0.790 Kg
Presentation
1
NiMh
- Recharge the battery before use with the charger ref.: 9014738. WARNING: Do not charge at a temperature above 70°C.
- Charge duration: 3h 30 min. max. 2 charges by year max.
- Never leave a battery in a discharged condition.
- No not open or pierce the battery.
- Do not put the battery into a fire, risk of explosion. Keep away (1m minimum) from from all types of flames, sparks or incandescent material.
- Do not create a short circuit on the battery terminals: danger of burns and explosion.
- The battery must be sheltered from the rain (IP X4).
- The battery must be accessible in order to carry out possible recharging (see instruction sheet 5055192).
- Suitable substrates for sticking: runners and box in aluminium, box in PVC (remove the protective films).The surfaces to be glued must be dry and clean.
- The ambient temperature when gluing should be between 20°C and 38°C.
- We recommend users run industrial tests in exactly the same conditions as those of the intended application and thereby ascertain that our product satisfies its
requirements. If in doubt, opt for the screwing solution.
- The battery must be replaced by a professional with an identical model.
- Do not put in the dustbin, this is a recyclable product.
- For more information about installation of the battery depending on the type of case, see Technical booklet ref: 5059076
Screw fixing
Glue fixing
- The 2 terminal connector (1) is for connection to the solar panel ref: 9014736
- The 4 terminal connector (2) is for connection to the T3.5 DC EHz motor
Recommendations
2
Mounting
3
Connection of the battery pack
4
1 -
Use solvent* to clean and wipe the surface for
gluing.
2 -
Pass the battery pack cable into the base.
3 -
Remove the protective paper from the adhe-
sive.
4 -
Press the battery pack onto the frame.
* Use a solvent containing a mixture of isopopyl
alcohol and water (50/50) or a heptane-based
solvent. Follow all the safety instructions concer-
ning the handling of solvents.
1
2
3
4
4
1
1
1
1
2
2
478,5
2
18
10
Ø 3mm
GB
BATTERY PACK AUTOSUN - 9014734
S.A.S. au capital de 5 000 000
€
- Z.I. Les Giranaux - BP71 - 70103 Arc-Les-Gray CEDEX - RCS GRAY B 425 650 090 - SIRET 425 650 090 00011 - n° T.V.A CEE FR 87 425 650 090
5055190A
Read carefully these
instructions before any use.
Fig. 1
Fig. 3
Fig. 4
15
1
2
503
30
27
Programming button
Connector for charger
The battery pack used in the Autosun solar system has the following functions:
- Store electrical energy provided by the solar panel.
- Supply electrical energy required by the motor.
- Enable programming of the motor using the programming button.
Technical data:
- NiMh battery - 12V / 2,2 Ah
- Battery life: approx. 5 years
- Storage temperature: -20° / +70°C
- Operating temperature: -20° / +70°C
- Storage time: max. 6 months at 20°C
- Protection index: IP X4
- Weight : 0.790 Kg
Presentation
1
NiMh
- Recharge the battery before use with the charger ref.: 9014738. WARNING: Do not charge at a temperature above 70°C.
- Charge duration: 3h 30 min. max. 2 charges by year max.
- Never leave a battery in a discharged condition.
- No not open or pierce the battery.
- Do not put the battery into a fire, risk of explosion. Keep away (1m minimum) from from all types of flames, sparks or incandescent material.
- Do not create a short circuit on the battery terminals: danger of burns and explosion.
- The battery must be sheltered from the rain (IP X4).
- The battery must be accessible in order to carry out possible recharging (see instruction sheet 5055192).
- Suitable substrates for sticking: runners and box in aluminium, box in PVC (remove the protective films).The surfaces to be glued must be dry and clean.
- The ambient temperature when gluing should be between 20°C and 38°C.
- We recommend users run industrial tests in exactly the same conditions as those of the intended application and thereby ascertain that our product satisfies its
requirements. If in doubt, opt for the screwing solution.
- The battery must be replaced by a professional with an identical model.
- Do not put in the dustbin, this is a recyclable product.
- For more information about installation of the battery depending on the type of case, see Technical booklet ref: 5059076
Screw fixing
Glue fixing
- The 2 terminal connector (1) is for connection to the solar panel ref: 9014736
- The 4 terminal connector (2) is for connection to the T3.5 DC EHz motor
Recommendations
2
Mounting
3
Connection of the battery pack
4
1 -
Use solvent* to clean and wipe the surface for
gluing.
2 -
Pass the battery pack cable into the base.
3 -
Remove the protective paper from the adhe-
sive.
4 -
Press the battery pack onto the frame.
* Use a solvent containing a mixture of isopopyl
alcohol and water (50/50) or a heptane-based
solvent. Follow all the safety instructions concer-
ning the handling of solvents.
1
2
3
4
4
1
1
1
1
2
2
478,5
2
18
10
Ø 3mm
GB
BATTERY PACK AUTOSUN - 9014734
S.A.S. au capital de 5 000 000
€
- Z.I. Les Giranaux - BP71 - 70103 Arc-Les-Gray CEDEX - RCS GRAY B 425 650 090 - SIRET 425 650 090 00011 - n° T.V.A CEE FR 87 425 650 090
5055190A
Read carefully these
instructions before any use.
Fig. 2
15
1
2
503
30
27
Programming button
Connector for charger
The battery pack used in the Autosun solar system has the following functions:
- Store electrical energy provided by the solar panel.
- Supply electrical energy required by the motor.
- Enable programming of the motor using the programming button.
Technical data:
- NiMh battery - 12V / 2,2 Ah
- Battery life: approx. 5 years
- Storage temperature: -20° / +70°C
- Operating temperature: -20° / +70°C
- Storage time: max. 6 months at 20°C
- Protection index: IP X4
- Weight : 0.790 Kg
Presentation
1
NiMh
- Recharge the battery before use with the charger ref.: 9014738. WARNING: Do not charge at a temperature above 70°C.
- Charge duration: 3h 30 min. max. 2 charges by year max.
- Never leave a battery in a discharged condition.
- No not open or pierce the battery.
- Do not put the battery into a fire, risk of explosion. Keep away (1m minimum) from from all types of flames, sparks or incandescent material.
- Do not create a short circuit on the battery terminals: danger of burns and explosion.
- The battery must be sheltered from the rain (IP X4).
- The battery must be accessible in order to carry out possible recharging (see instruction sheet 5055192).
- Suitable substrates for sticking: runners and box in aluminium, box in PVC (remove the protective films).The surfaces to be glued must be dry and clean.
- The ambient temperature when gluing should be between 20°C and 38°C.
- We recommend users run industrial tests in exactly the same conditions as those of the intended application and thereby ascertain that our product satisfies its
requirements. If in doubt, opt for the screwing solution.
- The battery must be replaced by a professional with an identical model.
- Do not put in the dustbin, this is a recyclable product.
- For more information about installation of the battery depending on the type of case, see Technical booklet ref: 5059076
Screw fixing
Glue fixing
- The 2 terminal connector (1) is for connection to the solar panel ref: 9014736
- The 4 terminal connector (2) is for connection to the T3.5 DC EHz motor
Recommendations
2
Mounting
3
Connection of the battery pack
4
1 -
Use solvent* to clean and wipe the surface for
gluing.
2 -
Pass the battery pack cable into the base.
3 -
Remove the protective paper from the adhe-
sive.
4 -
Press the battery pack onto the frame.
* Use a solvent containing a mixture of isopopyl
alcohol and water (50/50) or a heptane-based
solvent. Follow all the safety instructions concer-
ning the handling of solvents.
1
2
3
4
4
1
1
1
1
2
2
478,5
2
18
10
Ø 3mm
GB
BATTERY PACK AUTOSUN - 9014734
S.A.S. au capital de 5 000 000
€
- Z.I. Les Giranaux - BP71 - 70103 Arc-Les-Gray CEDEX - RCS GRAY B 425 650 090 - SIRET 425 650 090 00011 - n° T.V.A CEE FR 87 425 650 090
5055190A
Read carefully these
instructions before any use.
15
1
2
503
30
27
Programming button
Connector for charger
The battery pack used in the Autosun solar system has the following functions:
- Store electrical energy provided by the solar panel.
- Supply electrical energy required by the motor.
- Enable programming of the motor using the programming button.
Technical data:
- NiMh battery - 12V / 2,2 Ah
- Battery life: approx. 5 years
- Storage temperature: -20° / +70°C
- Operating temperature: -20° / +70°C
- Storage time: max. 6 months at 20°C
- Protection index: IP X4
- Weight : 0.790 Kg
Presentation
1
NiMh
- Recharge the battery before use with the charger ref.: 9014738. WARNING: Do not charge at a temperature above 70°C.
- Charge duration: 3h 30 min. max. 2 charges by year max.
- Never leave a battery in a discharged condition.
- No not open or pierce the battery.
- Do not put the battery into a fire, risk of explosion. Keep away (1m minimum) from from all types of flames, sparks or incandescent material.
- Do not create a short circuit on the battery terminals: danger of burns and explosion.
- The battery must be sheltered from the rain (IP X4).
- The battery must be accessible in order to carry out possible recharging (see instruction sheet 5055192).
- Suitable substrates for sticking: runners and box in aluminium, box in PVC (remove the protective films).The surfaces to be glued must be dry and clean.
- The ambient temperature when gluing should be between 20°C and 38°C.
- We recommend users run industrial tests in exactly the same conditions as those of the intended application and thereby ascertain that our product satisfies its
requirements. If in doubt, opt for the screwing solution.
- The battery must be replaced by a professional with an identical model.
- Do not put in the dustbin, this is a recyclable product.
- For more information about installation of the battery depending on the type of case, see Technical booklet ref: 5059076
Screw fixing
Glue fixing
- The 2 terminal connector (1) is for connection to the solar panel ref: 9014736
- The 4 terminal connector (2) is for connection to the T3.5 DC EHz motor
Recommendations
2
Mounting
3
Connection of the battery pack
4
1 -
Use solvent* to clean and wipe the surface for
gluing.
2 -
Pass the battery pack cable into the base.
3 -
Remove the protective paper from the adhe-
sive.
4 -
Press the battery pack onto the frame.
* Use a solvent containing a mixture of isopopyl
alcohol and water (50/50) or a heptane-based
solvent. Follow all the safety instructions concer-
ning the handling of solvents.
1
2
3
4
4
1
1
1
1
2
2
478,5
2
18
10
Ø 3mm
GB
BATTERY PACK AUTOSUN - 9014734
S.A.S. au capital de 5 000 000
€
- Z.I. Les Giranaux - BP71 - 70103 Arc-Les-Gray CEDEX - RCS GRAY B 425 650 090 - SIRET 425 650 090 00011 - n° T.V.A CEE FR 87 425 650 090
5055190A
Read carefully these
instructions before any use.
15
