background image

4

Installation 

4

Caution:

The connection of the hob to the gas network or gas cylinder must be made by means of a rigid 

copper or steel pipe with fittings complying with local regulations. These fittings are NOT supplied.

THIS OPERATION MUST BE MADE BY A QUALIFIED GAS INSTALLER

NOTE:

• The use of a gas cooking appliance produces heat and humidity in the place where it is installed.
• Therefore, you need to ensure the place is well ventilated, keeping the natural ventilation openings 

clear and use a cooker hood for extraction.

• Intensive or prolonged use of the appliance may require additional ventilation including opening 

a window.

• This appliance is only for flat bottomed pans.

This appliance is to be used for the preparation of food and drink only, and must not be used as a 

source of heat. Doing so may result in carbon monoxide poisoning and overheating of the hob.

Gas supply requirements

This hob is delivered pre-installed with gas jets (G20 : 20 mbar) suitable for natural gas. For use with 

other gases, please consult the injector table later in these instructions.  

Note:

 any change of jets MUST be carried out by a qualified gas installer only.

After completing the installation, ensure there is a gas tight seal around the bottom of all injectors 

using foam. Press on the injector with your finger so that the gas outlet is closed and check for any 

bubbles on the connection areas of the injectors.
Prior to installation, ensure that the local gas distribution and pressure are compatible with 

this appliance.

Ventilation 

This appliance must not be connected to a combustion products evacuation device. It shall be 

connected and installed in accordance with local installation regulations paying particular attention to 

the relevant requirements regarding ventilation.

What to do if you smell gas?

Do not try to light any appliance.
Do not touch any electrical switch.
Do not use phones in the building.
Immediately call your gas supplier from a different property.

WARNING:

 Read the instructions before using the appliance.

THIS APPLIANCE MUST BE EARTHED.
THIS HOB MUST BE INSTALLED BY A QUALIFIED GAS TECHNICIAN!

TRAG10584 - 200000010 - Cooke and Lewis 5 Burner Gas on Glass v3b Rv2.indd   4

13/06/2017   16:23

Содержание CLGOGUIT5



















Отзывы: