CONTROL SOLUTIONS ValuPoint 4 Скачать руководство пользователя | Manualshive

Страница: 45 / 95

background image

   Discrete, active low
   Dry contact, active open
Dry contact, active closed
    Pulse, high speed
Pulse, low speed (no hi-res)
Resistance, high resolution
   Resistance, low resolution
Position pot, hi-res, 1K-30K
Position pot, lo-res, 1K-30K

Thermistor, 10K type III hi-res, F
Thermistor, 10K type II hi-res, F
Thermistor, 3K type II hi-res, F
Thermistor, 20K type IV hi-res, F
Thermistor, 5K type II hi-res, F
Thermistor, 10K type III hi-res, C
Thermistor, 10K type II hi-res, C
Thermistor, 3K type II hi-res, C
Thermistor, 20K type IV hi-res, C
Thermistor, 5K type II hi-res, C

Thermistor, 10K type III lo-res, F
Thermistor, 10K type II lo-res, F
Thermistor, 3K type II lo-res, F
Thermistor, 20K type IV lo-res, F
Thermistor, 5K type II lo-res, F
Thermistor, 10K type III lo-res, C
Thermistor, 10K type II lo-res, C
Thermistor, 3K type II lo-res, C
Thermistor, 20K type IV lo-res, C
Thermistor, 5K type II lo-res, C

The designation hi-res and lo-res refer to the A/D resolution. There are two types
of A/D in the ValuPoint. The 'hi-res' A/D is a delta-sigma integrating converter that
produces 15-bit results (16-bit including sign, which is always positive with the input
circuitry implemented). The 'lo-res' A/D is a fast successive approximation converter
which produces 10-bit results.

Due to the fact that 'hi-res' conversion is relatively slow (about 1/4 second compared
to a few microseconds for lo-res), some combinations of I/O are not possible. Low
speed pulse counting to 10Hz is only possible when all inputs are in lo-res mode. All
discrete or dry contact modes are lo-res. High speed pulse counting (to 1kHz) is
possible with any combination of modes; however high speed counting uses dedicated
hardware and is only available in inputs channels 13 and 14.

Low speed pulse counting in combination with hi-res input conversions is possible, but
input pulse rate is limited to about 2Hz. To increase this limit to 10Hz, all analog

8. Object Map Page

file:///C:/AAA_CSI/Literature/2016 User Guides/VP4-BACnet User Gui...

5 of 10

11/3/2016 10:42 AM

«
...
43
44
45
46
47
...
»

Содержание ValuPoint 4
































































































Отзывы:

Нет отзывов

Похожие инструкции для ValuPoint 4

Бренд: Lattice Semiconductor Страницы: 30

Бренд: WAFER Страницы: 15

Бренд: K&K Страницы: 6

Бренд: Panamax Страницы: 16

Бренд: Sanhua Страницы: 3

Бренд: QED Страницы: 26

Бренд: Paradox Страницы: 3

Бренд: Eaton Страницы: 8

Бренд: ABB Страницы: 44

Бренд: Omega Страницы: 2

Бренд: Zmotion Страницы: 34

Бренд: Seiko Страницы: 30

ASC G Wi-Fi kit

Бренд: Waeco Страницы: 386

Бренд: KIPI Страницы: 44

Бренд: Gallagher Страницы: 2

Diaval AF Series

Бренд: Comeval Страницы: 10

SMARTCONNECT SMART/REP

Бренд: Zeta Alarm Systems Страницы: 48

Бренд: schmersal Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды