background image

26

W415-0889 / A / 08.11.10

COMBUSTIBLE FRAMING:

Sides, back, bottom and top 
of the appliance

0” to stand-offs

COMBUSTIBLE FINISHING:

Sides

2” to front edge of the appliance

Enclosure Top

84” from the bottom of the appliance

Recessed Depth

20 1/4”

Sides of the vent pipe

2”*

Bottom of the vent pipe

1”

Top of vent pipe

2”*

Ceiling

70” from the bottom of the appliance

* HORIZONTAL VENT SECTIONS: 

A minimum clearance of 1” at the bottom and sides and 2” at the top of 

the vent pipe in all horizontal runs to combustibles is required except for clearances in appliance enclosures.  
Horizontal vent sections within enclosures require a minimum clearance of 18” at the top of the vent pipe. 
See “MINIMUM CLEARANCE TO COMBUSTIBLE ENCLOSURES” section. Use 

fi

 restop spacer W010-1800 

(supplied) where vent pipe penetrates combustible walls.

* VERTICAL VENT SECTIONS: 

A minimum clearance of 1” all around the vent pipe on all vertical runs 

to combustibles is required except for clearances in appliance enclosures. Vertical vent sections within 
enclosures require a minimum clearance of 4” to the sides of the vent pipe. See “MINIMUM CLEARANCE 
TO COMBUSTIBLE ENCLOSURES” section. Use 

fi

 restop spacer W500-0367 (not supplied) where vent pipe 

penetrates combustible ceilings or 

fl

 oors.

5.1  MINIMUM CLEARANCE TO COMBUSTIBLES

        BACK WALL OF CHASE/ 
 ENCLOSURE (INCLUDING 
 ANY FINISHING MATERIALS) 

40 ¾”

16 

9

/

16

66 ½”

47”

33 ¼”

INSIDE

CHASE

OUTSIDE

CHASE

2”

4”

2”

4”

20 ¼”

6”

20 ¼”

40 ¾”

40 ¾”

Содержание CHDX40NT





















































Отзывы: