background image

19

W415-0858 / A / 02.14.11

CAUTION:

 Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper 

and dangerous operation. Verify proper operation after servicing. This appliance and its venting system 
should be inspected before use and at least annually by a qualifi ed service person. The appliance area must 
be kept clear and free of combustible materials, gasoline or other fl ammable vapors and liquids. The fl ow of 
combustion and ventilation air must not be obstructed.

1.

 

In order to properly clean the burner and pilot assembly, remove the logs, rocks and/or glass to 
expose both assemblies.

2.

 

Keep the control compartment, media, burner, air shutter opening and the area surrounding the logs 
clean by vacuuming or brushing, at least once a year.

3.

 

Check to see that all burner ports are burning. Clean out any of the ports which may not be burning or 
are not burning properly. 

4.

 

Check to see that the pilot fl ame is large enough to engulf the fl ame sensor and/or thermocouple / 
thermopile as well as reaches the burner.

5.

 

Replace the cleaned logs, rocks or glass. Failure to properly position the media may cause carboning 
which can be distributed in the surrounding living area.

6.

 

Check to see that the main burner ignites completely on all openings when turned on. A 5 to 10 
second total light-up period is satisfactory. If ignition takes longer, consult your local authorized dealer / 
distributor.

7.

 

Check that the gasketing on the sides, top and bottom of the door is not broken or missing. Replace if 
necessary.

8.

 

If for any reason the vent air intake system is disassembled, re-install and re-seal per the instructions 
provided for the initial installation.

40.1

MAINTENANCE

MAINTENANCE

MAINTENANCE

TURN OFF THE GAS AND ELECTRICAL POWER BEFORE SERVICING THE APPLIANCE.

APPLIANCE MAY BE HOT, DO NOT SERVICE UNTIL APPLIANCE HAS COOLED.

DO NOT USE ABRASIVE CLEANERS.

!

WARNING

9.3 FLAME 

CHARACTERISTICS

It’s important to periodically perform a visual check of the pilot and burner fl ames. Compare them to the illustra-
tions provided. If any fl ames appear abnormal call a service person.

3/8” - 1/2”

PILOT 

BURNER

FLAME MUST ENVELOP 
UPPER 3/8” TO 1/2” OF 
FLAME SENSOR

FLAME

SENSOR

ELECTRODE

54.1

10.0 MAINTENANCE

Содержание CDI-30GN





























Отзывы: