W415-4051 / C / 06.29.22
EN
4
table of contents
1.0 general information
6
1.1
rating plate / lighting instruction location 8
1.2
mobile home installation
8
2.0 dimensions
9
3.0 venting requirements
10
3.1
typical vent installations
12
3.2
special vent installations
13
3.2.1 periscope termination
13
3.2.2 reduced vent clearance to
combustibles
13
3.3
converting from 5/8" to 4/7" venting 14
3.4
vent terminal clearances
15
3.5
vent application flow chart
16
3.6 definitions
16
3.7
elbow vent length values
16
3.8
horizontal termination
17
3.9
vertical termination
19
4.0 framing
21
4.1 framing
22
4.1.1 see-thru framing (CBHD4STA)
22
4.1.2 peninsula framing (CBHD4PA)
22
4.2
minimum clearance to combustible
enclosures
23
4.2.1 see-thru (CBHD4STA)
23
4.2.2 peninsula (CBHD4PA)
23
5.0 venting installation
24
5.1
firestop spacer assembly
24
5.2
horizontal installation
26
5.3
vertical installation
27
5.4
using flexible vent components
28
5.4.1 horizontal air terminal installation
29
5.4.2 vertical air terminal installation
30
5.4.3 appliance vent connection
30
6.0 electrical information
31
6.1
hard wiring connection
31
6.2
receptacle wiring diagram
31
6.3
electronic wiring diagram
31
6.4
battery back-up installation
32
6.5
wiring diagram
33
7.0 gas installation
34
7.1
access panel for gas line connection 34
8.0 nailing tab installation
35
9.0 operation
36
10.0 operating instructions
37
10.1 operating instructions - for your safety
read before operating
37
10.2 lighting instructions
37
11.0 finishing
38
11.1 shipping bracket
38
11.2 main safety barrier removal /
installation
38
11.3 end safety barrier removal / installation
(CBHD4PA only)
39
11.4 main door removal / installation
40
11.5 end door removal / installation
(CBHD4PA only)
41
11.6 control panel removal
41
11.7 installing combustible board
42
11.7.1 finishing support adjustment
43
11.8 minimum mantel clearances
44
11.9 non-combustible facing material
45
11.10 log placement
46
11.10.1
glowing embers
48
11.10.2
charcoal embers
48
11.10.3
charcoal lumps
48
11.11 glass media installation
49
11.12 logo placement
49
12.0 adjustments
50
12.1 check pressure readings
50
12.2 venturi adjustment
50
12.3 restricting vertical vents
50
12.4 flame characteristics
51
13.0 maintenance
52
13.1 care of glass
53
13.2 annual maintenance
53
13.3 glass / door replacement
54
13.4 burner removal
54
13.4.1 log burner removal
54
13.4.2 glass burner removal
55
13.5 valve train replacement
55
14.0 replacement parts
56
14.1 CBHD4PA overview
57
14.2 CBHD4STA overview
58
14.3 glass burner assembly
59
14.4 glass burner valve train assembly
60
14.5 log burner assembly
61
14.6 log burner valve train assembly
62
15.0 accessories
63
16.0 troubleshooting
64
17.0 warranty
67
Changes, other than editorial, are denoted by a vertical line in the margin.
note:
