manualshive.com logo in svg

Continental Fireplaces BCDV42N, Инструкция по установке и эксплуатации, Страница: 2 / 48

Поделиться
Скачать
Continental Fireplaces BCDV42N Скачать руководство пользователя страница 2

2

W415-0778 / D / 09.13.12

TABLE OF CONTENTS

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

1.0 

INSTALLATION OVERVIEW 

3

2.0 INTRODUCTION 

4

2.1 DIMENSIONS 

5

2.2 GENERAL 

INSTRUCTIONS 

5

2.3 GENERAL 

INFORMATION 

6

2.4 

RATING PLATE INFORMATION 

7

3.0 VENTING 

8

3.1 

VENTING LENGTHS AND COMPONENTS 

9

3.2 

TYPICAL VENT INSTALLATIONS 

10

3.3 

SPECIAL VENT INSTALLATIONS 

11

3.3.1 PERISCOPE 

TERMINATION 

11

3.4 

MINIMUM AIR TERMINAL LOCATION CLEARANCES 

12

3.5 

VENT APPLICATION FLOW CHART 

13

3.6 DEFINITIONS 

13

3.7 

ELBOW VENT LENGTH VALUES 

13

3.8 HORIZONTAL 

TERMINATION 

14

3.9 VERTICAL 

TERMINATION 

16

4.0 INSTALLATION 

18

4.1 

WALL AND CEILING PROTECTION 

18

4.1.1 HORIZONTAL 

INSTALLATION 

19

4.1.2 VERTICAL 

INSTALLATION 

20

4.2 

USING FLEXIBLE VENT COMPONENTS 

20

4.2.1 HORIZONTAL 

AIR 

TERMINAL 

INSTALLATION 

21

4.2.2 VERTICAL 

AIR 

TERMINAL 

INSTALLATION 

22

4.2.3 VENT 

CONNECTION 

22

4.3 

USING RIGID VENT COMPONENTS 

23

4.3.1 HORIZONTAL 

AIR 

TERMINAL 

INSTALLATION 

23

4.3.2 

EXTENDED HORIZONTAL AIR TERMINAL INSTALLATION 

23

4.3.3 VERTICAL 

AIR 

TERMINAL 

INSTALLATION 

24

4.4 

MOBILE HOME INSTALLATION 

25

4.5 GAS 

INSTALLATION 

26

4.6 

OPTIONAL WALL SWITCH INSTALLATION 

26

5.0 FRAMING 

27

5.1 

MINIMUM CLEARANCE TO COMBUSTIBLES 

28

5.2 

MINIMUM ENCLOSURE CLEARANCES 

29

5.3 ALCOVE 

INSTALLATION 

30

5.4 

MINIMUM MANTEL CLEARANCES 

30

5.5 NAILING 

TAB 

INSTALLATION 

31

6.0 FINISHING 

31

6.1 

DOOR REMOVAL / INSTALLATION 

31

6.2 

L42 LOUVRE INSTALLATION 

32

6.3 

PORCELAIN REFLECTIVE PANELS 

32

6.4 GRATE 

INSTALLATION 

32

6.5 LOG 

PLACEMENT 

33

6.6 GLOWING 

EMBERS 

34

6.7 CHARCOAL 

EMBERS 

34

6.8 VERMICULITE 

34

6.9 CHARCOAL 

LUMPS 

34

6.10 LOGO 

PLACEMENT 

34

7.0 

OPTIONAL BLOWER INSTALLATION 

35

8.0 OPERATION 

36

9.0 ADJUSTMENTS 

37

9.1 PILOT 

BURNER 

ADJUSTMENT 

37

9.2 VENTURI 

ADJUSTMENT 

37

9.3 FLAME 

CHARACTERISTICS 

38

9.4 

RESTRICTING VERTICAL VENTS 

38

10.0 MAINTENANCE 

38

10.1 

CARE OF GLASS 

39

10.2 PLATED 

PARTS 

39

10.3 

GLASS / DOOR REPLACEMENT 

39

11.0 REPLACEMENTS 

40

12.0 TROUBLESHOOTING 

43

13.0 WARRANTY 

46

14.0 SERVICE 

HISTORY 

47

Содержание BCDV42N

















































Отзывы:

Нет отзывов