background image

7

W415-0812 / D / 08.16.12

2.3 GENERAL 

INFORMATION

When the appliance is installed at elevations above 4,500ft, and in the absence 
of speci

fi

 c recommendations from the local authority having jurisdiction, the 

certi

fi

 ed high altitude input rating shall be reduced at the rate of 4% for each ad-

ditional 1,000ft. 
This appliance is approved for bathroom, bedroom and bed-sitting room 
installations and is suitable for mobile home installation.
No external electricity (110 volts or 24 volts) is required for the gas system 
operation.  Expansion / contraction noises during heating up and cooling 
down cycles are normal and are to be expected. 
If utilizing one of Wolf Steel's trim or surround kits, follow the framing instructions and the 

fi

 nishing instructions, 

for removal of the top extension.

NOTE: The protective wrap on plated parts is best removed when the assembly is at room temperature 
but this can be improved if the assembly is warmed, using a hair dryer or similar heat source.

2.4  RATING PLATE INFORMATION

SERIAL NUMBER/
NO. DE SERIE:

BGD40 

W385-0656

CERTIFIED UNDER / HOMOLOGUE SELON LES NORMES: ANSI Z21.50b-2009 CSA 2.22b-2009 VENTED GAS FIREPLACE / FOYER AU GAZ AVEC EVACUATION

NOT FOR USE WITH SOLID FUEL.  FOR USE WITH 
COVERS AND GLASS DOOR CERTIFIED WITH THIS 
UNIT ONLY.

WARNING: 

DO NOT ADD ANY MATERIAL TO THE APPLIANCE, WHICH WILL COME IN 

CONTACT WITH THE FLAMES, OTHER THAN THAT SUPPLIED BY THE MANUFACTURER WITH 
THE APPLIANCE.   
MINIMUM CLEARANCE TO COMBUSTIBLE MATERIALS /
DEGAGEMENTS MINIMAUX DES MATERIAUX COMBUSTIBLES:
TOP, FLOOR, SIDES & BACK 

0”

DESSUS, PLANCHER, COTES ET ARRIERE
RECESSED DEPTH (CORNER INSTALLATION ONLY) 

25 1/4”

PROFONDEUR D’ENCASTRE (INSTALLATION DU COIN SEULEMENT)
VENT / EVENT 

1”

MANTEL HEIGHT / HAUTEUR DU MANTEAU 

5”*

*MAXIMUM HORIZONTAL EXTENSION/L’EXTENSION HORIZONTALE MAXIMALE: 3”.  SEE 
INSTRUCTION MANUAL FOR GREATER EXTENSIONS.  REFERER AU MANUEL 
D’INSTRUCTION POUR DES EXTENSIONS PLUS GRANDES.
MINIMUM AND MAXIMUM HORIZONTAL VENT LENGTHS ARE 10 INCHES AND 20 FEET 
RESPECTIVELY.  LES LONGUEURS HORIZONTALES MINIMALE ET MAXIMALE SONT 10 
POUCES ET 20 PIEDS RESPECTIVEMENT. 

WOLF STEEL LTD.

24 NAPOLEON ROAD, BARRIE, ON, L4M 0G8 CANADA

UN COMBUSTIBLE SOLIDE NE DOIT PAS ETRE UTILISE 
AVEC CET APPAREIL.  UTILISER AVEC LES 
COUVERTURES ET LES PORTES VITREES 
HOMOLOGUEES SEULEMENT AVEC CETTE UNITE.

AVERTISSEMENT: 

N’AJOUTEZ PAS A CET APPAREIL AUCUN MATERIAU DEVANT 

ENTRER EN CONTACT AVEC LES FLAMMES AUTRE QUE CELUI QUI EST FOURNI AVEC CET 
APPAREIL PAR LE FABRICANT.

THE APPLIANCE MUST BE VENTED USING THE APPROPRIATE WOLF STEEL VENT KITS.  SEE 
OWNERS INSTALLATION MANUAL FOR VENTING SPECIFICS.  PROPER REINSTALLATION AND 
RESEALING IS NECESSARY AFTER SERVICING THE VENT-AIR INTAKE SYSTEM.

L’APPAREIL DOIT EVACUER SES GAZ EN UTILISANT L’ENSEMBLE D’EVACUATION PROPRE A 
WOLF STEEL.  REFERER AU MANUEL D’INSTALLATION DE PROPRIETAIRE POUR 
L’EVACUATION PRECISE.  IL EST IMPORTANT DE BIEN REINSTALLER L’EVENT APRES AVOIR 
ASSURE LE MAINTIEN DU SYSTME DE PRISE D’AIR.

ELECTRICAL RATING / CLASSIFICATION: 115V, 0.82 AMP, 60HZ
OPTIONAL FAN KIT / ENSEMBLE DE VENTILATEUR FACULTATIF: GZ-550KT

 

9700539 (WSL) 

 

4001657 (NGZ) 

 4001658 

(NAC) 

 

4001659 

(WUSA)

FOYER A GAZ VENTILE DIRECT. HOMOLOGUE POUR INSTALLATION DANS UNE CHAMBRE A 

COUCHER, USE SALLE DE BAIN ET UN STUDIO.  APPROPRIE POUR INSTALLATION 
DANS UNE MAISON MOBILE SI SON INSTALLATION CONFROME AUX EXIGENCES DE LA 
NORME CAN/CSA Z240MH SERIE DE MAISONS MOBILES EQUIPEES AU GAZ, EN 
VIGUEUR AU CANADA OU AUX ETATS-UNIS DE LA NORME DE SECURITE ET DE 
CONSTRUCTION DE MAISONS MANUFACTUREES, TITRE 24 CFR, SECTION 3280.  
DANS LE CAS OU CETTE NORME D’ETATS-UNIS NE PEUT ETRE APPLIQUEE, SE 
REFERER A LA NORME RELATIVE AU CRITERE DE MESURES DE SECURITE CONTRE 
L’INCENDIE POUR LES INSTALLATION DANS LES MAISONS MANUFACTURES, LES 

SITES ET LES COMMUNAUTES, ANSI/NFPA 501A.

DIRECT VENT GAS FIREPLACE.  APPROVED FOR BEDROOM, BATHROOM AND BED-SITTING 
ROOM INSTALLATION.  SUITABLE FOR MOBILE HOME INSTALLATION IF INSTALLED IN 
ACCORDANCE WITH THE CURRENT STANDARD CAN/CSA Z240MH SERIES GAS 
EQUIPPED MOBILE HOMES, IN CANADA OR IN THE UNITED STATES THE 
MANUFACTURED HOME CONSTRUCTION AND SAFETY STANDARD, TITLE 24 CFR, 
PART 3280.  WHEN THIS US STANDARD IS NOT APPLICABLE USE THE STANDARD FOR 
FIRE SAFETY CRITERIA FOR MANUFACTURED HOME INSTALLATIONS, SITES AND 
COMMUNITIES, ANSI / NFPA501A.  

     BGD40GN 

  BGD40N 

BCDV400N 

MODEL 

BGD40P 

BCDV400P 

 BGD40GP

 

 

 0-4500FT (0-1370m) 

ALTITUDE / ELEVATION 

0-4500FT (0-1370m)

 

 

30,000 BTU/h 

 

INPUT / ALIMENTATION 

30,000 BTU/h

  

20,000 

BTU/h 

REDUCED  

INPUT / ALIMENTATION REDUITE 

20,000 BTU/h

 

 

 

MANIFOLD PRESSURE: 

3.5" WATER COLUMN 

MANIFOLD PRESSURE: 

10" WATER COLUMN

 

PRESSION AU COLLECTEUR:

 3.5" D'UNE COLONNE D'EAU 

PRESSION AU COLLECTEUR: 

10" D'UNE COLONNE D'EAU

 

MINIMUM SUPPLY PRESSURE:

 4.5" WATER COLUMN 

MINIMUM SUPPLY PRESSURE:

 11" WATER COLUMN

 

PRESSION D'ALIMENTATION MINIMALE: 

4.5" D'UNE COLONNE D'EAU 

PRESSION D'ALIMENTATION MINIMALE:

 11" D'UNE COLONNE D'EAU

 

MAXIMUM SUPPLY PRESSURE: 

7.0" WATER COLUMN 

MAXIMUM SUPPLY PRESSURE: 

13" WATER COLUMN

 

PRESSION D'ALIMENTATION MAXIMALE:

 7.0" D'UNE COLONNE D'EAU 

PRESSION D'ALIMENTATION MAXIMALE: 

13" D'UNE COLONNE D'EAU

 

For rating plate location, see “INSTALLATION OVERVIEW” section.
This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

NOTE: The rating plate must remain with the appliance at all times. It must not be removed.

NG

LP

Altitude (FT)

0-4,500

0-4500

Max. Input (BTU/HR)

30,000

30,000

Max. Output Steady State (BTU/HR)

20,400

20,400

Min. Inlet Gas Supply Pressure

4.5" Water Column

11" Water Column

Max. Inlet Gas Supply Pressure

7" Water Column

13" Water Column

Manifold Pressure (Under Flow Conditions)

3.5" Water Column

10" Water Column

FOR YOUR SATISFACTION, THIS APPLIANCE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION AND 
QUALITY! 

 

S

CE 

CE

SE WITH

E WITH 

 WITH THIS 

WITH THIS 

PPLIANCE, WHICH WILL COME IN 

WHICH WILL COME IN 

PPLIED BY THE MANUFACTURER WITH

PPLIED BY THE MANUFACTURER WIT

ALS /

ALS /

OMBUSTIBLES:

BUSTIBLES:

ATION ONLY) 

LLATION DU COIN SEULEMENT)

LATION DU COIN SEULEMENT)

MANTEAU

MANTEAU 

ENSION/L’EXTENSION HORIZONTALE M

NSION/L’EXTENSION HORIZONTALE 

R GREATER EXTENSIONS.  REFERER 

REATER EXTENSIONS.  REFERER

S EXTENSIONS PLUS GRANDES.

XTENSIONS PLUS GRANDE

RIZONTAL VENT LENGTHS ARE 

ZONTAL VENT LENGTHS A

RS HORIZONTALES MINIM

S HORIZONTALES MINI

EMENT. 

T. 

G8 CANAD

8 CANA

UN CO

UN CO
AVE

AVE
C

C

4001657 (NGZ)

400

4001659 (WUSA)

400165

LL

T. HOMOL

T. HOMO

LE DE BAIN ET

LE DE BA

N MOBILE SI SON INS

MOBILE SI SON IN

SA Z240MH SERIE DE M

A Z240MH SERIE DE

CANADA OU AUX ETATS-UN

CANADA OU AUX ETATS-UN

CTION DE MAISONS MANUFACTU

ON DE MAISONS MANUFACTU

E CAS OU CETTE NORME D’ETATS-

OU CETTE NORME D’ETATS-

RER A LA NORME RELATIVE AU CRITE

RME RELATIVE AU CRITE

CENDIE POUR LES INSTALLATION D

S INSTALLATION D

S

S

EL 

BGD40P 

D40P 

ELEVATION

ELEVATION

0-4500FT (0-1

0-4500FT (0-

ALIMENTATION

ALIMENTATION 

30,000 BTU

30,000 BT

IMENTATION REDUITE 

20,000 B

MENTATION REDUITE 

20,000 

PL

PL

PL

LUMN 

UMN 

MANIFOLD PRESSURE:

NIFOLD PRESSURE: 

10

10

E D'EAU

D'EAU

PRESSION AU COLLECT

RESSION AU COLLEC

R COLUMN

R COLUMN 

MINIMUM SUPPLY PR

MINIMU

ONNE D'EAU

ONNE D'EAU

PRESSION D'ALIME

PRES

WATER COLUMN 

ATER COLU

MAXIMUM SUPP

MAXIMU

E COLONNE D'EAU

COLONNE D'EA

PRESSION D'A

PRESSION

66.8%

BCDV40

Содержание BCDV40-N





















































Отзывы: