Contec VPC-3100-G Series Скачать руководство пользователя страница 96

Страница: 96 / 115

—

Hardware RAID Setup

—

VPC-3100-G Series Reference Manual

FAQ and Troubleshooting

This section consists of FAQ and troubleshooting related to mirror cards. When you run into trouble,
refer to the relevant items.

FAQ

◆

I am not sure in which direction the data between storage

are copied.

⚫

When a malfunctioning storage is replaced with hot-plugging, data are copied from the
existing storage to the replacement storage.

⚫

When a malfunctioning storage is replaced with cold-plugging, data are copied from the
existing storage to the replacement storage.

◆

I replaced storages connected to the mirror card.

⚫

If both storages are functioning properly, data are not copied.

⚫

If one storage is malfunctioning, data are not copied between storages.

◆

I want to use an existing storage to make a mirroring

configuration from a backup storage.

If you want to configure mirroring using a storage as a backup, which is different from the case of
two storages used in an existing mirroring configuration, follow the procedure shown below.

<Steps>

Turn the PC OFF.

Remove both existing storages from the mirror card.

For instructions on how to remove the storage, see

in the [

Setup (page32

)].

Install only the backup storage to the mirror card.

For instructions on how to install the storage, see “Setting the Storage” in the [

Hardware

Setup (page32

)].

Turn the PC ON.

Then, connect the storage to be used in the mirroring configuration to the empty drive in the
mirror card, and rebuild the system.

After the rebuild finishes properly, the two connected storages are contained in a mirroring
configuration.

Содержание VPC-3100-G Series




















































































































Результаты поиска

Содержание VPC-3100-G Series

Отзывы:

Похожие инструкции для VPC-3100-G Series

Бренды по названию

Популярные бренды

Contec VPC-3100-G Series, Справочное руководство

Результаты поиска

Содержание VPC-3100-G Series

Отзывы:

Похожие инструкции для VPC-3100-G Series

Бренды по названию

Популярные бренды