Contec FX-DS540-APDL-U Скачать руководство пользователя страница 33

Страница: 33 / 91

3. Setup

FX-DS540-APDL-U

Setup

Wall Installation

In case of using the supported screw

Refer to the main unit installation drawing to drive the screws into a wall and hang the main unit on

them.

(1)

(2)

(3)

(1) Drive the screws into the wall. The dimensions are shown in the figure above. (2 locations)
(2) Attach the AP case such that the two screws on the wall insert into the wall-mount holes on the case.
(3) Slide the AP unit down to hold it in place.

Figure 3.2. Wall Installation

CAUTION

Do not obstruct the ventilation slits. This can cause the temperature inside the product to rise and

can damage the components inside.

WARNING

Do not install this product downward or on a ceiling.

It can be overheated inside to catch fire.

POW

WRX

WL IN

L IN

Содержание FX-DS540-APDL-U




























































































Результаты поиска

Содержание FX-DS540-APDL-U

Отзывы:

Бренды по названию

Популярные бренды

Contec FX-DS540-APDL-U, Руководство пользователя

Результаты поиска

Содержание FX-DS540-APDL-U

Отзывы:

Бренды по названию

Популярные бренды