background image

Important Safety Instructions

1.  Read these instructions.

2.  Keep these instructions.

3.  Heed all warnings.

4.  Follow all instructions.

5.  Do not use this apparatus near water.

6.  Clean only with dry cloth.

7.  Do not block any ventilation openings. Install in accordance with the 

manufacturer’s instructions.

8.  Do not install near any heat sources such as radiators, heat risters, 

stoves, or other apparatus (including amplifiers) that produce heat.

9.  Do not defeat the safety purpose of the polarized or 

grounding-type plug. A polarized plug has two blades with one wider 

than the other. A grounding type plug has two blades and a third 

grounding prong. The wide blade or the third prong are provided for 

your safety. If the provided plug does not fit into your outlet, consult an 

electrician for replacement of the obsolete outlet.

10.  Protect the power cord from being walked on or pinched particularly at 

plugs, convenience receptacles, and the point where they exit from the 

apparatus.

11. 

Only use attachments/accessories specified by the manufacturer.

12. 

Use only with the cart, stand, tripod, bracket, or table specified by the 

manufacturer, or sold with the apparatus. When a cart is used, use caution 

when moving the cart/apparatus combination to avoid injury from 

tip-over.

13.  Unplug the apparatus during lightning storms or when unused for long 

periods of time.

14. 

Refer to all qualified service personnel. Servicing is required when the 

apparatus has been damaged in any way, such as power-supply cord or 

plug is damaged, liquid has been spilled or objects have fallen into the 

apparatus, the apparatus has been exposed to rain or moisture, does not 

operate normally, or has been dropped.

Содержание STS-K015-01

















Отзывы: