6
476-016C_v01
Fruit/vegetables
Centrifuging speed
Cabbage
II
Fennel
I
Raspberries
I
Carrots
II
Melons
I
Apricots
I
Nectarines
I
Cucumbers
I
Kiwi
I
Tomatoes
I
Celery
II
Grapes
I
Part names
1
Juice extractor motor
a
I-0-II switch
b
TURBO button
c
skimmer
d
vacuum cup
e
supply cord
2
Bowl
f
juice spout
3
Bowl insert
g
fin
4
Filter
5
Lid
6
Locking bar
7
Bowl for small fruits
8
Pusher
9
Juice collector
10
Foam separator
11
Lid of collector
12
Pulp collector
13
Brush
14
Gasket
Preparations for operation
(disassembling)
Disassemble the juice extractor before first
usage and clean the parts in contact with
processed product.
1
Place the juice extractor near the socket on the firm,
clean and dry surface.
A
B
2
Pull down the locking bar
(6)
so that the tracks moved
out of grooves of the lid
(5)
from position
1
to position
2
.
3
Take the pusher
(8)
out and remove the bowl
(7)
and
lid
(5)
.
4
Then remove the bowl
(2)
including the insert
(3)
and
filter
(4)
.
5
Then, disassemble the insert
(3)
from the bowl
(2)
.
6
Finally, remove the gasket
(14)
from the bowl
(2)
,
as washing the bowl
(2)
with the gasket
(14)
on is not
recommended, but only after disassembling it.
Wash the disassembled parts (apart from the
motor) carefully in hot water and wash-up
liquid. You can clean them in dishwasher in
max temp. 60ºC (apart from the motor and
filter). After drying carefully start assembling
the clean parts.
Preparations for operation
(assembling)
1
Assemble the gasket
(14)
into the bowl
(2)
making sure
that the flat surface of the gasket
(14)
is facing the top.
2
Align the bowl
(2)
with the gasket
(14)
to the motor
(1)
,
so that the juice spout
(f)
was placed exactly in the casing
(1)
groove and 4 buckles from the upper part of the motor
(1)
were placed inside the 4 grooves in the bottom of the
bowl
(2)
.
3
Align the insert
(3)
to the bowl
(2)
so that the fin
(g)
of the
insert
(3)
is placed in the cutting of the bowl
(2)
over the juice
spout.
4
Put the filter
(4)
inside and check if it is well mounted and
rotates easily.
5
Put the lid
(5)
so that the fin
(g)
of the insert
(3)
was
placed in the cutting of the lid
(5)
.
6
We call your attention to proper assembling. The fin
(g)
of the insert
(3)
should be in the same line as the cutting on
the bowl
(2)
and the cutting in the lid
(5)
.
7
Pull the locking bar
(6)
up, so that the rolls moved into
grooves of the lid
(5)
from position
2
to position
1
(you will
hear a characteristic clicking sound).
8
Each time insert a bowl for small fruit
(7)
on the feeder
opening of the cover
(5)
.
9
Put the pusher
(8)
into the chute so that the V-shaped
hole was put on the knife inside the chute.
10
Put the pulp collector
(12)
under the lid
(5)
in the
following way: lean the collector and place it under the insert
(3)
and lid
(5)
, then push it towards the motor
(1)
.
11
Put the juice collector
(9)
so that the juice spout
(f)
was
inside the collector
(9)
.
C
