CONQUEST Magna BS 2SL Basic, Руководство оператора

Страница: 30 / 36

N.B. : to adjust the solution jet from the tank cleaning accessory, turn the knob (8) on the
accessory itself ( Fig.8 ).
N.B. : to adjust the intensity of the solution jet from the
tank cleaning accessory, turn the knob
(9) on the accessory itself
( Fig.9 ).
N.B. : to stop the solution jet, use the lever (10) on the tank cleaning accessory ( Fig.10 ).
N.B. : the place designated for this operation must comply with current environmental protection
regulations.
10. The vacuum hose from the retainers present inside the recovery tank.
11. Rinse the inside of the vacuum hose with a jet of running water.
12. Repeat the operations in reverse order to reassemble all the parts.
9
9
8
8
7
7
10
10
EXTRAORDINARY MAINTENANCE
REPLACING THE SQUEEGEE BODY RUBBER BLADES
Ensuring the integrity of the squeegee body's rubber blades guarantees better floor cleaning and drying
results, as well as a longer service life for the vacuum motor. In order to replace the squeegee body's
rubber blades, do the following:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “ SECURING THE MACHINE ”).
CAUTION : these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
3. Extract the vacuum hose (1) from the vacuum nozzle on the squeegee body (
Fig.1
).
4. Completely unscrew the knobs (2) in the squeegee body's pre-assembly ( Fig.2 ).
5. Remove the squeegee body from the slits in the squeegee connector ( Fig.3 ).
6. Remove the rear rubber blade compression plate, and release the stopper (3) at the rear of the
squeegee ( Fig.4 ).
7. Remove the rear rubber blade (4) from the squeegee body ( Fig.5 ).
8. Completely unscrew the knobs (5) in the squeegee body's pre-assembly ( Fig.6 ).
9. Remove the front rubber blade (6) from the squeegee's internal body ( Fig.7 ).
10. Repeat the operations in reverse order to reassemble all the parts.
N.B.
: Before using the machine, remember to adjust the squeegee body: see the section titled
“ ADJUSTING THE SQUEEGEE BODY'S RUBBER BLADES ”.
N.B. : It is recommended to replace both squeegee body blades in order to ensure good results
when drying the floor.
2 3 1
1 2
4
3
6 5
4 5
7
6
REPLACING THE BRUSH HEAD SPLASH GUARD
If the splash guard rubber blades of the brush head side casing are damaged they cannot work properly,
namely they cannot convey the dirty detergent solution towards the squeegee, therefore the splash
guard rubber blades need to be checked. To replace the brush head splash guards, proceed as follows:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “ SECURING THE MACHINE ”).
CAUTION : these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
3. Open the machine's left lateral carter (1) ( Fig.1 ).
4. Remove the left splash guard body (2) and move the fixing anchors (3) on the brush head body
into the maintenance position ( Fig.2 ).
5. Remove the rear rubber blade compression plate (4), and release the stopper (5) on rubber blade
compression plate ( Fig.3 ).
6. Remove the splash guards (6) from the left splash guard body and replace it with a new one or
else turn it around ( Fig.4 ).
7. Repeat the operations in reverse order to reassemble all the parts.
8. Repeat the operations just carried out also for the right side casing as well.
3 1 2
1
2
5
4
3
4
6
REPLACING THE SIDE SQUEEGEE SPLASHGUARD RUBBER BLADES
If the splash guard rubber blades of the side squeegee are damaged they cannot work properly,
namely they cannot convey the dirty detergent solution towards the squeegee, therefore the rubber
blades need to be checked. To replace the brush head splash guards, proceed as follows:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “ SECURING THE MACHINE ”).
3. Stand at the back of the machine.
CAUTION : these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
4. Extract the vacuum hose (1) from the vacuum nozzle on the squeegee body ( Fig.1 ).
5. Completely unscrew the knobs (2) in the squeegee body's pre-assembly ( Fig.2 ).
6. Remove the squeegee body from the slits in the squeegee connector ( Fig.3 ).
7. Using the right equipment, not supplied with the machine, remove the screw (3) ( Fig.4 ).
8. Using the right equipment, not supplied with the machine, remove the nut (3) ( Fig.5 ).
9. Remove the left side squeegee (5) from the machine ( Fig.6 ).
10. Using the right equipment, not supplied with the machine, remove the screws fixing the splash
guard rubber blades (6) ( Fig.7 ).
11. Remove the old splash guard rubber blades (7) and replace them with new ones ( Fig.8 ).
12. Repeat the operations in the reverse order and reassemble all the part, then pass on to the right
side squeegee.
N.B. : remember to put the blade compression plate (8) between one splash guard rubber
blade and the other ( Fig.8 ).
2 3 1
1 2
5 6 4
3 4 5
31