manualshive.com logo in svg

Conergy Active System, Инструкция для владельца и по установке

Поделиться
Скачать
Conergy Active System Скачать руководство пользователя страница 23

E

N

G

L

IS

H

Conergy AS

Owners Manual

    Electrical Connections to the System

  Electrical Connections to the System

Note:

1.

2.

3.

4.

5.

6.

7.1  Electrical connection for electric AES systems

For safe performance this water heater is fitted with a Thermostat, and an over temperature cut-out. 
These devices should not be tampered with or removed. Do not operate this water heater without the 
electrical thermostat and over temperature cut-out in the circuit.
The electric element is only connected in models using an electric AES system. No connection is 
made to the electric element for gas AES systems.

For electric AES systems, there are numerous connection alternatives depending on the local electrical 
supply tariffs and the costumers’ preferences.  The correct alternative should be established with the 
Conergy dealer prior to installation.  Diagrams for the two most common alternatives are below.

|

|

|

All electrical work must comply with local regulations and AS3000.

All electrical work must be conducted by a suitability licensed electrician.

Refer to the Owner’s Manual supplied with the tank for more detailed information on the specific 
requirements of the storage tank.

Do not turn on power to the system until it is filled with water.

The electrical supply to the pump module must be continuously available.  Off Peak power 
must not be used as both temperature regulation and frost protection are governed by the pump 
module

If the supply cord to any appliance is damaged, it must be replaced by the manufacturer or its 
service agent or a similarly qualified person in order to avoid a hazard.

The electric AES is designed for single phase, 240V A.C. supply only.
For a single element tank, connections are made at the terminal block under the element cover.
For  a  twin  element  tank,  connections  are  made  at  the  terminal  block  under  the  lower  element 
cover.  An active connection is made only to terminal A2, the top element.

Figure 5: 

 Single Element Tank Wiring Diagram

EARTH

RED

BLACK

A1

N

E

LE

M

E

N

T

Figure 6: 

 Twin Element Tank Wiring Diagram

ELEMENT

ELEMENT

BLUE

RED
RED

BLACK

A1
A2

N

EARTH

Содержание Active System































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды