manualshive.com logo in svg

Conergy Active System, Инструкция для владельца и по установке

Поделиться
Скачать
Conergy Active System Скачать руководство пользователя страница 14

E

N

G

L

IS

H

Conergy AS

Owners Manual

1

   Collector Installation

5.1

After  selecting  the  solar  collector 
location,  the  final  check  before 
installation  is  that  the  available  roof 
space  is  sufficient  for  the  solar 
collectors being installed.

The length up the roof must be at least 
3 metres for all installations.

Please note: Roof areas smaller than the minimum measurements will make installation and 
later service work more difficult.

Installing the collectors

The procedure for solar collector installation is as follows:

Figure 3:

 Collector Installation Area

Figure 4

:  Collector Installation General Assembly

1 panel    =   2000 mm
2 panels  =   3000 mm
3 panels  =   4000 mm

500

500

500

500

3000 mm

System

Roof space width required

1 panel

2000 mm

2 panel

3000 mm

3 panel

4000 mm

1.  Mark a point for the bottom left corner of the collector installation. This point should be at least  
  500 mm up from the roof edge and 500 mm to the side of any obstruction or roof edge.

2.  Place one end of the collector mounting rail 

(Detail D, 60-3028)

 adjacent to the location marked  

  in step 1, and laid horizontally across the roof to the right.

3.  Locate two roof trusses which are under the collector mounting rail (as near as possible to the  
  outer edges of the rail).  Clip two collector straps

 (Detail E, 60-4011)

 to the collector mounting

  rail where the trusses pass under the mounting rail.

  Collector Installation

Содержание Active System































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды