manualshive.com logo in svg

Conergy Active System, Инструкция для владельца и по установке

Поделиться
Скачать
Conergy Active System Скачать руководство пользователя страница 19

E

N

G

L

IS

H

Conergy AS

Owners Manual

1

Connections for open circuit systems with a PM-600

 
1.  Ensure that the pump module is installed in an  
  accessible position.

2.  Apply thread tape or a suitable sealant to the  
  thread of the ¾” BSP to ½” compression union  

 

  (P/No 60-1029).  Screw the union into the top  
  outlet) socket on the right side of the storage  
  tank. Fasten the Collector Hot Connection    
  (Section 8.0, Step 2) into the compression union.

3.  Apply thread tape or a suitable sealant to the  
  large thread of the ¾” to ½” BSP brass fitting  

 

  (P/No 60-5066) and screw into the bottom (inlet)  
  socket, on the right side of the storage tank.

4.  Take the PM-600 module and fasten a Gland  
  Union (P/No 60-1032) to the Ball Valve (P/No  

 

  35-8008) on the lower pump fitting and the    
  Check Valve (P/No 35-8009) on the upper pump  
  fitting.

5.  Apply thread tape or a suitable sealant to one end of the ½” BSP brass union (P/No 60-5065)  
  and fasten it into the lower Gland Union attached to the Ball Valve.

5.  Loosely attach one end of the 225mm Flexible Connector (P/No 60-1115) to the brass nipple on 
  the PM-600 module.  Loosely attach the other end to the bottom (inlet) fitting of the storage  
  tank.

6.  With the flexible connector loosely fitted, move the pump module into position on the storage  
  tank and fix in place with the self-drilling screws supplied (P/No 75-3047).  Ensure the flexible  
  connector is not kinked in any way, and the pump module is vertical.  Tighten the loose nuts on  
  the flexible connector.

7.  Make the Collector Cold Connection (Chapter 8.0, Step 1) to the upper pump fitting of the PM- 
  600 module.

8.  Open the Ball Valve (P/No 35-8008) by turning the screw slot until it is vertical.

9.  Turn on the mains water supply to the unit and fill the storage tank as normal.  Check for leaks in  
  the system and fix as required.

6.2

  Connections at the Storage Tank

60-1032

35-8009

35-8008

60-1032

60-5065

60-1115

60-5066

Содержание Active System































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды