Condair TE Series Скачать руководство пользователя страница 9

Страница: 9 / 44

Product Overview

Condair TE

Product Overview

The Condair Ceiling Mounted Evaporative Humidifier is a ceiling-embedded cassette humidifier that directly

humidifies the room. Each unit is installed inside the ceiling (or in an open ceiling) with a decorative cover

that can be opened and closed easily for maintenance. Each unit operates independently and provides

reliable performance that is not affected by the system settings of the air conditioner (temperature, air

flow, etc.).

Figure 1: Components

3.1

Functional Description

Supply water passes through the supply header and is dripped evenly across the Humidification module.

Water drips downward through the media. Supplied air passes through the cassette where it evaporates

water on the surface of the media to create humidified air. Water that has not evaporated continues to

flow down the media where it picks up any dust and other debris, and drips onto the drain pan.

Figure 2: Functional Description

When operation is initiated via pressing of the operation button or an external command signal input,

when the humidistat is turned ON, and in other such situations, the fan will remain OFF at the start of

humidification operations and water will be continuously supplied to wet the humidification module which

washes away odour-causing elements and similar brought in via the supply water. This initial supply

water intake process lasts for 10 minutes.
After initial supply water intake, the unit will switch to intermittent water supply (time sharing system, or

TSS), the fan will begin operating and humidification will start.

Humidification

module

Water droplet

collection panel

Drain pan

Fan

Water supply

Supplied air

Drain

Cover

(Grille)

Humidified air

Water supply hose

Terminal block

Control unit

Float switch

Check valve

Water supply hose

(including orifice for controlling flow rate)

Water supply filter

Pressure regulator

Water shutoff valve

Water solenoid valve

Media

Humidified air

Drain pan

Header

Water supply

Supplied air

Drain

Level sensor

Содержание TE Series













































Результаты поиска

Содержание TE Series

Отзывы:

Похожие инструкции для TE Series

Бренды по названию

Популярные бренды

Condair TE Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание TE Series

Отзывы:

Похожие инструкции для TE Series

Бренды по названию

Популярные бренды