Condair TE Series Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 44

background image

25

Maintenance

Condair TE

6.6

Removing the Water Supply Strainer

Figure 9: Water supply strainer

To remove the water supply strainer (and clean the tubular mesh):

1. Remove the humidifier cover. Refer to chapter

6.3 on page 23

2. Remove the drain cap from the drain pan, and remove the white connector of the water leakage

sensor. Refer to chapter

6.4 on page 23

.

3. Remove the drain pan (and humidification module). Refer to chapter

6.5 on page 24

4. Remove the water supply strainer cap. The tubular mesh can now be removed and cleaned.

•

Clean the tubular mesh with water.

5. Replace the equipment by following these instructions in reverse order.

6.7

Cleaning the Humidifier Filter

Figure 10:

Cleaning the humidifier air filter

Turn off the humidifier and remove power from the unit.

1.  Open the humidifier cover then remove the filter from it.
2.  Wash the filter with water. A neutral detergent may be used to clean the filter if necessary.
3.  Dry the filter in a shaded location.
4.  After it has dried, reattach the filter to the cover.
5.  You may then restore power to the humidifier.

Water supply hose (with

built-in check valve)

Check valve

Water supply strainer

Strainer cap

O-ring

Gasket

Tubular mesh

Air outlet side

Filter

21.1 x 8.5 in (535 x 215 mm)

«
...
24
25
26
27
28
...
»

Содержание TE Series













































Отзывы:

Нет отзывов

Похожие инструкции для TE Series

Бренд: Qlima Страницы: 84

Бренд: Comfort Zone Страницы: 6

Бренд: BRAYER Страницы: 32

Бренд: BRAYER Страницы: 23

Бренд: universalblue Страницы: 37

Бренд: Parker Hiross Страницы: 272

Бренд: OKBABY Страницы: 55

Бренд: Wood’s Страницы: 8

Бренд: Nortec Страницы: 125

Бренд: KDK Страницы: 52

Бренд: Lanaform Страницы: 36

Бренд: Kruger Страницы: 32

Бренд: VDL Страницы: 16

Бренд: Equator Страницы: 12

Бренд: Haier Страницы: 9

1700 - 6 Gallon Humidifier

Бренд: Kenmore Страницы: 32

Streamline SL-16

Бренд: GeneralAire Страницы: 10

Бренд: Orbegozo Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды