84
85
EN
EN
VR3510
VR3510
WATER FLOW SETTING
You can adjust the water flow using the mobile app. The
water flow cannot be changed via the remote control. The
water flow will be set to a medium level. Use the mobile
app to adjust the water flow.
USING THE REMOTE CONTROL
1. Cleaning planning
2. Moving forward
3. Turning left
4. Local TURBO cleaning
5. Start/pause charging
6. Automatic cleaning / pause
7. Cleaning/pause
8. Turning right
9. Suction of dirt out of the container
10. Setting the suction power
1
2
3
4
5
6
7
8
9
10
Note: To ensure that all the correct settings are effective,
you must point the remote control at the front of the
robotic vacuum cleaner from close proximity.
Time setting
1. Press the button
on the remote control to enter
the time setting, the Sunday symbol flashes on the
LCD.
2. Press the left and right buttons to select the day of the
week and press the button
to confirm it, then the
LCD will automatically switch to the clock setting.
3. Press the up and down buttons to set the hour and
press the left and right buttons to move to the minute
setting.
4. After setting the current time, point the remote control
at the front of the robotic vacuum cleaner and press
the button
to confirm all time settings. Failure to
do so will invalidate your settings.
5. This completes the time setting for both the remote
control and the robotic vacuum cleaner.
Cleaning plan
1. Press the button
on the remote control to enter
the plan setting function, the Sunday symbol flashes
on the LCD.
2. Press the left and right buttons to select the day of the
week and press the button
to confirm it, then the
LCD will automatically switch to the clock setting.
3. Press the up and down buttons to set the hour and
press the left and right buttons to move to the minute
setting. Then point the remote control at the front of
the robotic vacuum cleaner and press the button
to confirm this plan setting for the robotic vacuum
cleaner.
4. When one plan setting is completed, the remote
control automatically moves to the next plan setting.
If you do not want to continue with the setting, press
the exit button
or wait 10 seconds for the setting
to finish automatically.
5. This completes the time setting for both the remote
control and the robotic vacuum cleaner.
Cancelling the cleaning plan
1. Press the button
on the remote control, the
Sunday symbol flashes on the LCD and the symbols
for the days of the week you have planned appear.
2. Press the left and right buttons to select the day of the
week you have planned, and press and hold the button
for 3 seconds to cancel the plan. You can also select
the next planned day you want to cancel, or press the
exit button
or wait 10 seconds for the setting to
finish automatically.
DAILY MAINTENANCE
Main brush (clean regularly)
1. Turn the appliance over and press the latch on the
main brush cover to pull it out.
2. Remove dust from inside and from inside the main
brush with a small brush and clean the main brush.
3. Reassemble the main brush and press firmly on the
cover until the latch clicks into place.
Latch
The main brush
Side brush
(clean regularly)
1. Turn the appliance over and pull the side brush up.
2. Remove hair and dirt and refit the side brush.
3. Make sure the left side brush (L) and right side brush
(R) correspond to the L and R symbols on the bottom
cover. Push the L and R side brushes to reinstall them.
Note: Replace the side brushes every 3 to 6 months to
ensure their cleaning effect.
Dust container and filter grid
(clean regularly)
1. Press the button and pull the dust container
backwards.
2. Open and clean the dust container.
Cleaning the filter grid
(clean regularly)
1. After prolonged use, remove the foam filter and HEPA
filter.
2. Rinse the foam filter and HEPA filter under water.
3. Wipe the individual parts and let them dry freely.
4. After drying, gradually install them in the correct order:
grid - foam filter - HEPA filter.
Filter holder
Foam filter
Grid
Container
release
button
HEPA filter
Note:
•
Rinse the filter grid with clean water and do not add
any detergent.
•
Do not clean the filter grid with a brush or fingers.
•
Allow the filter grid to air dry for at least 24 hours.
Wiping module
(clean after each use)
1. Remove and clean the cloth.
2. Wipe the water tank dry.
Sensors
(clean regularly)
Clean the sensors with a soft cloth as follows:
1. Clean the sensors along the wall to the right.
2. Three cliff sensors at the bottom of the appliance.
3. Infra-red anti-collision sensor in front of the appliance.
4. Protection against electric shock and docking station
contacts at the bottom of the appliances (turn off the
appliance during cleaning).
5. Docking station signal transmission area.
Cliff sensor
TOF sensor
Charging
contact
Sensors
(clean every month)
Anti-collision
sensor
Infra-red
charging sensor
LDS laser range-
finder
Anti-collision sensor
for radar sensor
Battery
•
The appliance is equipped with high-performance
lithium-ion batteries. To maintain battery
performance, keep the appliance charged every day.
•
If the appliance is not used for a long time, turn it off
and store it properly. Charge it at least every 3 months
to prevent damage to the batteries due to excessive
discharge.
