78
79
VR2110, VR2100
VR2110, VR2100
EN
EN
1
Filter strainer cover
2
Dust container button
3
Wall sensor
2
3
1
Docking station
1
Power indicator light
2
Signal transmission area
3
Base charging contacts
4
Catch groove
5
Cover plate
6
Cable passage
7
AC adapter socket
8
Winding pin
5
4
3
2
1
6
7
8
List of parts
1
Docking station 1x
2
Remote control 1x
3
Wiping cloth 2x
4
HEPA foam filter 3x (for VR2100 2x)
5
Magnetic strip 1x
6
Adapter 1x
7
Cleaning brush 1x
8
Left and right brush 2x
9
HARDFLOOR brush 1x (VR2110 only) CAUTION!
Cannot be used on carpets, cleaning may be
interrupted.
10
CARPET brush 1x
11
Electrically operated water tank 1x (VR2110 only)
12
PET brush 1x (VR2110 only)
13
Main brush cover 1x (VR2110 only)
suitable for HARDFLOOR and PET brushes
14
Main brush cover with steel wire 1x (suitable for
CARPET brush)
15
Hanging water tank 1x (VR2100 only)
1
2
3
6
7
8
4
5
9
10
11
12
13
14
15
KEY FEATURES
Cleaning / ON/OFF
•
Press briefly to start or pause cleaning.
•
Press and hold for 3 seconds to switch the appliance
on or off.
•
Long press for 15 seconds to force the appliance to
shut down under unusual circumstances.
Charging / Local cleaning
•
Press briefly to start or pause charging.
•
Long press to start local cleaning.
Indicator light
•
Orange: Normal operation or charging.
•
Red: Abnormal condition or low battery.
•
Red-orange: The appliance is not connected to the
network.
Wi-Fi reset
•
Press both buttons simultaneously for 3 seconds.
INSTALLATION
1. Connect the power cord and store the excess
cable length in the cable compartment.
2. Place the docking station against the wall and
connect the power.
Note:
•
Provide a space of min. 0.5 m on both sides of the
docking station and min. 1.5 m in front of the station.
•
If the power cord is stretched vertically to the ground,
the appliance may pull it out and the docking station
may be switched off.
•
In normal condition, the charging indicator light is on
when switched on, and off when charged.
3. Do not move the docking station or expose it to
direct sunlight.
Note:
Direct sunlight will interfere with the docking
station signal and the appliance may not return to the
docking station properly.
4. Installing the side brush
Make sure the left side brush (L) and right side brush
(R) markings correspond to the L and R markings on
the bottom cover. Push the side brushes L and R until
you hear a “click” sound.
5. Putting the appliance into operation and charging
To switch the robot on, press and hold the button .
If the power indicator light is normally on, charge the
robot in the docking station.
Note
: If the appliance does not start due to a low
battery, charge it in the docking station and it will start
automatically. Normally, the appliance can only operate
when the battery level is ≥20 %.
6. Connecting a mobile app (you can skip this step)
Read the instructions for connecting Wi-Fi and connect
the mobile app.
7. Start of cleaning
After switching on the robot, briefly press the button
on the robot or start cleaning using the mobile app
(you can pause the appliance by pressing any button
during use).
Note:
•
The sweeping robot cannot be used to remove fluids.
•
If the battery charge level is less than 20 %, the
appliance cannot operate. In this case, recharge it.
•
If the battery charge level is less than 20 %, the
appliance automatically returns to the docking station.
•
Before use, remove various wires (including the
docking station power cord) from the floor to prevent
outages and damage to objects or wires when the
appliance catches these wires.
8. Installing the wiping module
a) Installing the wiping cloth: glue the wiping cloth
straight to the bottom of the water tank.
Model VR2100 - Hanging water tank
Model VR2110 - Electrically operated water tank
Note:
Clean the wiping cloth after use to keep it in good
condition.
b) Fill the water tank: open the cover and fill the tank
with water.
Model VR2100 - Hanging water tank
