Comtech EF Data CRS-180 Скачать руководство пользователя страница 91

Страница: 91 / 134

CRS-180 70/140 MHz IF 1:1 Redundancy Switch

MN/CRS180.IOM

Cables and Connections

Revision 11

5–33

5.5 Cabling to the CDM-710G

For information on configuring the CRS-180 70/140 MHz 1:1 Redundancy Switch

with the CDM-710G High-Speed Satellite Modems for 1:1 operation, see:

•

Chapter 4. MODEM

AND

SWITCH

CONFIGURATION

•

CDM-710G High-Speed Satellite Modem Installation and Operation Manual

(CEFD P/N MN-CDM710G)

For information on the cables and cable assemblies specified in this section, see:

•

Appendix A. CABLE DRAWINGS

5.5.1 CRS-180



CDM-710G Control and IF Interface Connections Using

Cabling Kit KT/12554

Figure 5-29 shows the CRS-180-to-CDM-710G control and IF interface connections. The Comtech

EF Data KT/12554 CRS-180 70/140 MHz IF 1:1 Redundancy Kit provides all control and IF

connection components.

Figure 5-29 NOTES:

Use of the XF/BNC-MF-50-75 transformers (Item 2) is required on the ‘J7 | Rx’

and ‘J8 | Tx connectors, located on the antenna side of the switch, when you

supply a 75

Ω Rx/Tx connection.

Use of the XF/BNC-MF-50-75 transformers (Item 2) on the Rx A and Rx B ports,

located on the modem side of the switch, is dependent on the CDM-710G’s

factory configuration for 50

Ω

or 75

Ω

Rx operability. If the modems in use are

configured as 50

Ω

Rx units, the transformers will not be used on the Rx side

and the 50

Ω

cable (Item 4) will be used in place of the 75

Ω

cable (Item 3).

To provide User access to modem “Fault Summary Relay,” Control ‘Y’ Cable

CA/WR13011-4, sold separately, is available for use in place of the

CA/WR12135-1 cable.

Control Cable CA/WR12135-1 will mute the Offline Modem’s Tx IF. If this is not

desired, then an alternate cable, Control Cable CA-0000187, sold separately, is

available for use in place of the CA/WR12135-1 cable.

You must order terrestrial data interface components/kits separately. See Sect.

5.5.2 for CDM-710G terrestrial data interface configuration and connection

examples and details.

Содержание CRS-180






































































































































Результаты поиска

Содержание CRS-180

Отзывы:

Comtech EF Data CRS-180, Инструкция по установке и эксплуатации, Страница: 91 / 134

Результаты поиска

Содержание CRS-180

Отзывы: