Comtech EF Data CRS-180 Скачать руководство пользователя страница 52

Страница: 52 / 134

CRS-180 70/140 MHz IF 1:1 Redundancy Switch

MN/CRS180.IOM

Modem and Switch Configuration

Revision 11

4–12

4.4.2 IP Redundancy Configuration

Before continuing you must remember that, when you use the Command Line

Interface (CLI), you can make configuration changes to the Online modem only.

Make sure to press ‘S’ to “Save Parameters to permanent storage” after making any

changes to an active CLI page. This ensures that the configuration change is also

applied to the Backup modem.

Do these steps for setup of a CDM-570/A 1:1 IP Redundancy System:

Step

Task

Use a Layer 2 switch (preferred) or hub to establish an Ethernet connection between the two modems.

Before you connect the modems to the CRS-180, you must first use the modem CLI to configure the

following CDM-570LAL IP operation settings:

•

Disable 1:1 Redundancy operation – From the

Main Menu

, press ‘

’ to open the

1:1 Redundancy

Configuration

page.

Press ‘

’ to toggle 1:1 Redundancy as

[Disabled].

•

From the

Main Menu

, press ‘

’ to open the

Administration

page.

Press ‘

’ (

Administration



Working Mode

) and set both modems to the same Working

Mode.

Press ‘

’ (

Administration



Feature Configuration

) and make sure to configure, using all

applicable submenus, both modems to have the same IP-related operability and settings.

For each modem, use the CLI to enter a unique IP Address that is on the same subnet:

•

From the Main Menu, press ‘

’ to open the

Interface Configuration

page.

•

Press ‘

’ to open the

Ethernet Interface

page (

Interface Configuration



Ethernet Interface

•

Press ‘

’ to enter the IP Address.

Verify that you can ping from one modem to the other:

•

From the Main Menu, press ‘

’ to open the

Operations and Maintenance

page.

•

Press ‘

’ to open the

Diagnostics

page (

Operations and Maintenance



Diagnostics

•

Press ‘

’ and then enter the IP Address of the other modem in the redundant pair.

Re-enable 1:1 Redundancy operation – From the

Main Menu

, press ‘

’ to open the

1:1 Redundancy

Configuration

page.

•

Press ‘

’ to toggle 1:1 Redundancy as

[Enabled]

Power down both modems.

Connect the modems to the CRS-180.

CDM-570/CDM-570L/CDMR-570L Satellite Modem Installation and Operation

Manual (CEFD P/N MN/CDM570L.IOM): Sect. H.6 Cabling with the CDM-570L.

Содержание CRS-180






































































































































Результаты поиска

Содержание CRS-180

Отзывы:

Comtech EF Data CRS-180, Инструкция по установке и эксплуатации, Страница: 52 / 134

Результаты поиска

Содержание CRS-180

Отзывы: