Comtech EF Data CRS-180 Скачать руководство пользователя страница 22

Страница: 22 / 134

CRS-180 70/140 MHz IF 1:1 Redundancy Switch

MN/CRS180.IOM

Introduction

Revision 11

1–4

1.3 Functional Description

The CRS-180 performs the Tx and Rx coaxial switching required for redundant modem operation

with an outdoor BUC and LNB.

1.3.1 Switch Operation with CDM-625/A, -760, -750, -570/A, -710G, -710, or

-700 Modems

The CRS-180 is configured with two modems to form a complete 1:1 redundant modem system.

Within the CRS-

180, a redundanc

y controller continually monitors the status of faults for both

modems to determine which modem should be Online and Offline. The control cables between

the modems and the CRS-180 include four signal groups:

•

First

serial full-duplex communication lines are routed from one modem to the other

modem via the CRS-180.

Using these lines, t

his Online modem can interrogate the Offline

modem at regular intervals to determine its configuration. If a difference in configuration is

detected, the

Online modem will reconfigure the Offline modem so that the configurations

are always synchronized. This process is

entirely automatic

– if the Offline modem is

replaced, it does not have to be manually reprogrammed to match the

Online modem.

•

Second

the Modem’s Unit

, Tx and

Rx faults signals from both modems are routed to the

CRS-180. This allows the redundancy controller to always know the health status of both

modems.

•

Third

the Online/Offline signals are routed from the CRS-180 to each modem. Based on the

modem faults, the CRS

-180 will determine which modem should be Online and Offline. In

the event that both modems indicate faults through some malfunction, the CRS

-180 will

select

, by default,

Modem ‘A’.

•

Fourth, +12V is routed from each modem to the CRS-180 for operational power. This power

from both modems is diode OR’d so that the CRS-180 remains active if power is lost from

one of the modems.

IF Switching – The CRS-180 provides IF redundancy

, but when switching occurs, it

accommodates more than just the IF signals.

On the Rx side,

the Rx IF signal from the LNB is split

in a power divider to continuously drive both the Online and Offline demodulator. The Offline

demodulator can then maintain lock so that it is ready to quickly assume Online status for

receive traffic when a switchover is required.

Data Switching

is accomplished inside each modem, in the data interface itself. A ‘Y’ cable

connects both the Online modem and the Offline modem to the terrestrial data source.

Transmit data drives both modems in parallel so that the standby modulator is always ready to

come Online. Termination impedance for the modem line receivers is active in the Online

modem. On th

e Rx side of the interface,

TRI-

STATE

control of the Offline modem line drivers

Содержание CRS-180






































































































































Результаты поиска

Содержание CRS-180

Отзывы:

Comtech EF Data CRS-180, Инструкция по установке и эксплуатации, Страница: 22 / 134

Результаты поиска

Содержание CRS-180

Отзывы: