Comtech EF Data CRS-180 Скачать руководство пользователя страница 57

Страница: 57 / 134

CRS-180 70/140 MHz IF 1:1 Redundancy Switch

MN/CRS180.IOM

Modem and Switch Configuration

Revision 11

4–17

4.6 Configure Switch DIP Settings

The “Switch Conditions” DIP switches are set depending upon the type of Tx or Rx

traffic conditions that are resultant of switchover. Some modems have additional

settings or alarm masks that affect conditions – see your pertinent modem

Installation and Operation Manual for detailed explanations.

Figure 4-3 shows the DIP switches located on the antenna side of the CRS-180. The table

provided here shows the settings that determine “Switch Conditions” – the switchover

functionality for a given redundancy configuration.

“Switch Conditions” DIP Settings

DIP

Left Switch

Right Switch Result

Down (Off)

Down

Switchover upon a Unit fault

Down

Switchover upon a Unit or Tx Traffic fault

Down

Switchover upon a Unit or Rx Traffic fault

Switchover upon a Unit or Tx Traffic or Rx Traffic fault

Figure 4-3. CRS-180 “Switch Conditions” DIP Switches

Содержание CRS-180






































































































































Результаты поиска

Содержание CRS-180

Отзывы:

Comtech EF Data CRS-180, Инструкция по установке и эксплуатации, Страница: 57 / 134

Результаты поиска

Содержание CRS-180

Отзывы: