Computex FP-30 Скачать руководство пользователя страница 6

Страница: 6 / 18

Technical Information on SPI Flash Programmer FP-30

Oct. 15, 2019

(Second Edition)

Technical Information on SPI Flash Programmer FP-30 (Second Edition)

Go through the required procedures as stated under Foreign Exchange and Foreign Trade Control Law in exporting (including the case where

travellers directly carry) this product or providing this product for residents outside Japan.



No part of this manual, whether in whole or in part, may be adapted, copied or reproduced without prior permission.



The content of and the specifications of this product are subject to change without prior notice.



Computex Co., Ltd. shall not be held liable for any loss or damage arising from the use of this product although all possible measures have been

taken by Computex Co., Ltd. in good faith to ensure the quality of the product.



Contact us for any questions, feedback, comments, requests or anything of concern to you (or in the event of malfunction) regarding this product or

misprinting or missing information within this manual.



Other names of CPUs etc. mentioned in this manual are trademarks or registered trademarks of their respective manufacturers.



COMPUTEX is registered trademark of Computex Co., Ltd. in Japan.

Содержание FP-30


















