manualshive.com logo in svg

Compaq Evo W8000, Справочник по аппаратуре

Поделиться
Скачать
Compaq Evo W8000 Скачать руководство пользователя страница 45

Hardware Upgrades 

Installing a Hard Drive in the Removable Hard Drive Cage (Bays 1 to 3)

 

The removable hard drive cage canbe configured with up to three 
1.0-inch hard drives or two 1.6-inch hard drives. Other than using 
different screw holes, the installation for both types of drives is 
basically the same.  
 

Prior to installing a SCSI device, see “SCSI Devices” in Appendix B. 

To install a hard drive in the removable hard drive cage: 

1.  Shut down the operating system properly, then turn off the 

workstation and any external devices. Disconnect the power cord 
from the grounded AC outlet. 

2.  Remove the workstation access panel. See “Removing the 

Workstation Access Panel” in this chapter. 

3.  Removable hard drive cage. See “Removing ad Replacing the 

Removable Hard Drive Cage” in this chapter. 

4.  Remove four of the hard drive screws (top group of screws) from 

the side of the air plenum located at the front of the workstation. 
See “Locating the Hardware Screws” in this chapter. 

 

If only one SCSI hard drive is used, install it in bay 2. 

2-30 

Compaq Evo Workstation W8000 Hardware Reference Guide

 

Содержание Evo W8000





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды