Compaq D315 - Desktop PC страница 31 Скачать руководство пользователя

Страница: 31 / 76

Troubleshooting Guide

2–17

Troubleshooting Without Diagnostics

Solving Audio Problems

If your computer has audio features and you encounter audio
problems, see the common causes and solutions listed in the
following table.

Solving Audio Problems

Problem

Cause

Solution

Sound does not come
out of the speaker or
headphones.

Software volume
control is turned down.

Double-click the

Speaker

icon on

the taskbar, then set volume by
adjusting the volume slider.

CD-ROM or DVD
volume control on the
front of the computer is
turned down.

Turn the volume control knob on
front of computer to increase the
volume.

The external speakers
are not turned on.

Turn on the external speakers.

External speakers
plugged into the wrong
audio jack.

See the sound card documentation
for proper speaker connection.

Audio cable not
connected.

Connect audio cable between CD
or DVD-ROM drive and the system
board.

Headphones or
devices connected to
the line-out connector
mute the internal
speaker.

Turn on and use headphones or
external speakers, if connected, or
disconnect headphones or external
speakers.

Volume is muted.

1. From the

Control Panel

program, click

Sound, Speech

and Audio Devices,

then click

Sounds and Audio Devices.

2. Click the

Mute

check box to

remove the check mark from
the box.

292974-002.book Page 17 Tuesday, July 9, 2002 5:46 PM

Содержание D315 - Desktop PC













































































Результаты поиска

Содержание D315 - Desktop PC

Отзывы:

Похожие инструкции для D315 - Desktop PC

Бренды по названию

Популярные бренды

Compaq D315 - Desktop PC, Руководство по устранению неисправностей

Результаты поиска

Содержание D315 - Desktop PC

Отзывы:

Похожие инструкции для D315 - Desktop PC

Бренды по названию

Популярные бренды