Compaq D315 - Desktop PC страница 24 Скачать руководство пользователя

Страница: 24 / 76

2–10

Troubleshooting Guide

Troubleshooting Without Diagnostics

“Invalid system disk”
message is displayed.

A diskette that does not
contain the system files
needed to start your
computer has been
inserted in the drive.

When drive activity stops, remove
the diskette and press the

Spacebar.

The computer should

start up.

Diskette error has
occurred.

Restart your computer by pressing
the power

button.

Nonsystem disk/NTLDR

missing

message.

The system is trying
to start from a
nonbootable diskette.

Remove the diskette from the
drive.

Cannot Boot to Diskette.

Diskette is not
bootable.

Replace with a bootable diskette.

Diskette boot has been
disabled in Computer
Setup.

Run Computer Setup and enable
diskette boot in

Storage > Boot

Order.

Removable media boot
has been disabled in
Computer Setup.

Run Computer Setup and enable
Removable Media Boot in

Storage > Storage Options.

Diskette MBR
validation is enabled.

Run Computer Setup and disable
Diskette MBR Validation in

Storage > Storage Options.

Solving Diskette Problems

(Continued)

Problem

Cause

Solution

292974-002.book Page 10 Tuesday, July 9, 2002 5:46 PM

Содержание D315 - Desktop PC













































































Результаты поиска

Содержание D315 - Desktop PC

Отзывы:

Похожие инструкции для D315 - Desktop PC

Бренды по названию

Популярные бренды

Compaq D315 - Desktop PC, Руководство по устранению неисправностей

Результаты поиска

Содержание D315 - Desktop PC

Отзывы:

Похожие инструкции для D315 - Desktop PC

Бренды по названию

Популярные бренды